HP Engage Go 10 Maintenance and Service Guide - Page 38

Ambient light sensor (ALS), Cameras

Get HP Engage Go 10 PDF manuals and user guides View all HP Engage Go 10 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Ambient light sensor (ALS) To remove the ambient light sensor, use this procedure and illustration. Before removing the ambient light sensor, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 21). 2. Remove the display assembly (see Display assembly on page 21). 3. Disconnect the battery cable from the system board (see Battery on page 23). Remove the ambient light sensor: 1. Use tweezers to disconnect the cable from the reverse ZIF connector on the system board (1). 2. Use tweezers to lift the sensor out of the computer (2). The sensor is secured with adhesive. To install the ambient light sensor, reverse the removal procedure. Cameras To remove the cameras, use this procedure and illustration. Before removing the cameras, follow these steps: 1. Prepare the computer for disassembly (see Preparation for disassembly on page 21). 2. Remove the display assembly (see Display assembly on page 21). 3. Disconnect the battery cable from the system board (see Battery on page 23). Remove the cameras: 1. Use tweezers to disconnect the camera cables from the reverse ZIF connectors on the system board (1). 30 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
Ambient light sensor (ALS)
To remove the ambient light sensor, use this procedure and illustration.
Before removing the ambient light sensor, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
21
).
2.
Remove the display assembly (see
Display assembly
on page
21
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
23
).
Remove the ambient light sensor:
1.
Use tweezers to disconnect the cable from the reverse ZIF connector on the system board
(1)
.
2.
Use tweezers to lift the sensor out of the computer
(2)
. The sensor is secured with adhesive.
To install the ambient light sensor, reverse the removal procedure.
Cameras
To remove the cameras, use this procedure and illustration.
Before removing the cameras, follow these steps:
1.
Prepare the computer for disassembly (see
Preparation for disassembly
on page
21
).
2.
Remove the display assembly (see
Display assembly
on page
21
).
3.
Disconnect the battery cable from the system board (see
Battery
on page
23
).
Remove the cameras:
1.
Use tweezers to disconnect the camera cables from the reverse ZIF connectors on the system board
(1)
.
30
Chapter 4
Removal and replacement procedures