HP Integrity rx1620 Installation Guide, Second Edition - HP Integrity rx1620 - Page 37

Inserting DIMM into Memory Slot, Installing Additional Memory

Get HP Integrity rx1620 PDF manuals and user guides View all HP Integrity rx1620 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

Installing and Configuring Installing Additional Memory CAUTION To ensure that memory modules are not damaged during removal or installation, power off the server and unplug the power cord from the AC power outlet. Wait until the power on/off LED on the control panel turns off before removing or installing memory. Observe all ESD safety precautions before attempting this procedure. Failure to follow ESD safety precautions could result in damage to the server. Step 2. Determine the memory slot location to be used for the DIMM(s) being installed. See "DIMM Locations". Step 3. Ensure that the latches of the DIMM socket are in the open (outward) position. Step 4. Align the DIMM with the socket located on the system board. NOTE The DIMMs and the DIMM sockets are keyed to prevent improper insertion of the modules. Step 5. Gently and evenly push down on the top edge of the DIMM until it seats in the socket. Ensure the extraction levers are in the closed position. CAUTION Avoid applying too much pressure to the DIMM when inserting the module into the socket. It is possible to damage the socket connector. Touch only the outer card edge of the module. Figure 3-23Inserting DIMM into Memory Slot Step 6. Replace the cover, reconnect all cables, and turn on the power. Chapter 3 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Chapter 3
Installing and Configuring
Installing Additional Memory
37
CAUTION
To ensure that memory modules are not damaged during removal or installation,
power off the server and unplug the power cord from the AC power outlet. Wait until
the power on/off LED on the control panel turns off before removing or installing
memory.
Observe all ESD safety precautions before attempting this procedure. Failure to
follow ESD safety precautions could result in damage to the server.
Step 2.
Determine the memory slot location to be used for the DIMM(s) being installed. See “DIMM
Locations”.
Step 3.
Ensure that the latches of the DIMM socket are in the open (outward) position.
Step 4.
Align the DIMM with the socket located on the system board.
NOTE
The DIMMs and the DIMM sockets are keyed to prevent improper insertion of the
modules.
Step 5.
Gently and evenly push down on the top edge of the DIMM until it seats in the socket. Ensure the
extraction levers are in the closed position.
CAUTION
Avoid applying too much pressure to the DIMM when inserting the module into the
socket. It is possible to damage the socket connector. Touch only the outer card edge
of the module.
Figure 3-23Inserting DIMM into Memory Slot
Step 6.
Replace the cover, reconnect all cables, and turn on the power.