HP ML330 HP ProLiant ML330 Generation 3 Server Maintenance and Service Guide - Page 18

Front Bezel, Pull up on the bezel locking latch until it disengages.

Get HP ML330 - ProLiant - G3 PDF manuals and user guides
UPC - 613326960790
View all HP ML330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Removal and Replacement Procedures Front Bezel CAUTION: To prevent equipment damage or data loss, be sure that the server is powered down, all cables are disconnected from the back of the server, and the power cord is disconnected from the grounded (earthed) AC outlet before removing the front bezel. To remove the component: 1. Power down the server. Refer to "System Power Down" in this chapter. 2. Pull up on the bezel locking latch until it disengages. 3. Rotate the bezel upward and slide it away from the chassis. A small amount of force may be necessary to detach the bezel. To replace the component, reverse the removal procedure. IMPORTANT: When replacing the front bezel, be sure to place the top hinge points in the chassis before rotating the front bezel downward to its original position. HP ProLiant ML330 Generation 3 Server Maintenance and Service Guide 2-5 HP CONFIDENTIAL Codename: Flashback Part Number: 322375-004 Last Saved On: 1/5/04 11:38 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Removal and Replacement Procedures
Front Bezel
CAUTION:
To prevent equipment damage or data loss, be sure that the server is powered
down, all cables are disconnected from the back of the server, and the power cord is
disconnected from the grounded (earthed) AC outlet before removing the front bezel.
To remove the component:
1.
Power down the server. Refer to “System Power Down” in this chapter.
2.
Pull up on the bezel locking latch until it disengages.
3.
Rotate the bezel upward and slide it away from the chassis. A small amount of force may
be necessary to detach the bezel.
To replace the component, reverse the removal procedure.
IMPORTANT:
When replacing the front bezel, be sure to place the top hinge points in the chassis
before rotating the front bezel downward to its original position.
HP ProLiant ML330 Generation 3 Server Maintenance and Service Guide
2-5
HP CONFIDENTIAL
Codename: Flashback Part Number: 322375-004 Last Saved On: 1/5/04 11:38 AM