HP ML330 HP ProLiant ML330 Generation 3 Server Maintenance and Service Guide - Page 64

System ID Switch, Jumper Settings, SCSI Device Jumper Settings

Get HP ML330 - ProLiant - G3 PDF manuals and user guides
UPC - 613326960790
View all HP ML330 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

Component Identification System ID Switch The system ID switch is reserved for use by authorized service providers only. Do not change the indicated default settings. Jumper Settings SCSI Device Jumper Settings No two SCSI devices connected to the same SCSI controller can have the same SCSI ID. If another SCSI device is connected to the controller, check its SCSI ID before beginning the installation procedure for the additional device. Jumpers located on each device set the SCSI ID. For more information, refer to the SCSI device option documentation. IDE Device Jumper Settings When installing any IDE devices (ATA hard drives, ATAPI CD-ROM drives, or ATAPI tape drives), be sure that the jumper on the device is set to Cable Select (CS). This setting allows the cable to automatically assign the device ID of an IDE drive attached to the cable. For information on installing and cabling IDE devices, refer to the setup and installation guide. 4-8 HP ProLiant ML330 Generation 3 Server Maintenance and Service Guide HP CONFIDENTIAL Codename: Flashback Part Number: 322375-004 Last Saved On: 1/5/04 11:43 AM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Component Identification
System ID Switch
The system ID switch is reserved for use by authorized service providers only. Do not change
the indicated default settings.
Jumper Settings
SCSI Device Jumper Settings
No two SCSI devices connected to the same SCSI controller can have the same SCSI ID. If
another SCSI device is connected to the controller, check its SCSI ID before beginning the
installation procedure for the additional device. Jumpers located on each device set the
SCSI ID. For more information, refer to the SCSI device option documentation.
IDE Device Jumper Settings
When installing any IDE devices (ATA hard drives, ATAPI CD-ROM drives, or ATAPI tape
drives), be sure that the jumper on the device is set to Cable Select (CS). This setting allows
the cable to automatically assign the device ID of an IDE drive attached to the cable. For
information on installing and cabling IDE devices, refer to the setup and installation guide.
4-8
HP ProLiant ML330 Generation 3 Server Maintenance and Service Guide
HP CONFIDENTIAL
Codename: Flashback Part Number: 322375-004 Last Saved On: 1/5/04 11:43 AM