HP Mini 100e HP Mini 100e Education Edition - Maintenance and Service Guide - Page 44

Hard drive assembly, Remove the following components

Get HP Mini 100e - Education Edition PDF manuals and user guides View all HP Mini 100e manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

3. Remove the WLAN module (3) by pulling the module away from the slot at an angle. Reverse this procedure to install the WLAN module. Hard drive assembly NOTE: The hard drive assembly spare part kit includes a bracket, screws, rubber grommets, and Mylar tape. Description Hard drive assembly (160-GB, 5400-RPM) Hard drive connector Spare part number 621406-001 619571-001 Before removing the hard drive assembly, follow these steps: 1. Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the computer on, and then shut it down through the operating system. 2. Disconnect all external devices connected to the computer. 3. Disconnect the power from the computer by first unplugging the power cord from the AC outlet and then unplugging the AC adapter from the computer. 4. Remove the following components: a. Battery (see Battery on page 30) b. Service access cover (see Service access cover on page 31) Remove the hard drive assembly: 1. Remove the 4 Phillips 2.0x5.0 screws (1) that secure the assembly to the computer. 36 Chapter 4 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
3.
Remove the WLAN module
(3)
by pulling the module away from the slot at an angle.
Reverse this procedure to install the WLAN module.
Hard drive assembly
NOTE:
The hard drive assembly spare part kit includes a bracket, screws, rubber grommets, and
Mylar tape.
Description
Spare part number
Hard drive assembly
(160-GB, 5400-RPM)
621406-001
Hard drive connector
619571-001
Before removing the hard drive assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn
the computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet
and then unplugging the AC adapter from the computer.
4.
Remove the following components:
a.
Battery (see
Battery
on page
30
)
b.
Service access cover (see
Service access cover
on page
31
)
Remove the hard drive assembly:
1.
Remove the 4 Phillips 2.0x5.0 screws
(1)
that secure the assembly to the computer.
36
Chapter 4
Removal and replacement procedures