HP Pavilion 11-h110nr HP Pavilion 11 x2 PC Maintenance and Service Guide - Page 52

Solid-state drive

Get HP Pavilion 11-h110nr PDF manuals and user guides View all HP Pavilion 11-h110nr manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Solid-state drive Description 128-MB m2 SATA solid-state drive 64-MB m2 SATA solid-state drive Spare part number 742736-001 742737-001 Before removing the solid-state drive, follow these steps: 1. Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on, and then shut it down through the operating system. 2. Disconnect the power from the tablet by unplugging the power cord from the tablet. 3. Disconnect all external devices from the tablet. 4. Remove the display enclosure (see Display enclosure on page 31). 5. Disconnect the tablet battery cable from the system board (see Sensor board on page 32). Remove the solid-state drive: 1. Remove the Phillips PM1.85×3.00 screw (1) that secures the solid-state drive to the system board. 2. Lift the side of the solid-state drive (2) opposite the slot until it rests at an angle. 44 Chapter 5 Removal and replacement procedures

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Solid-state drive
Description
Spare part number
128-MB m2 SATA solid-state drive
742736-001
64-MB m2 SATA solid-state drive
742737-001
Before removing the solid-state drive, follow these steps:
1.
Turn off the tablet. If you are unsure whether the tablet is off or in Hibernation, turn the tablet on,
and then shut it down through the operating system.
2.
Disconnect the power from the tablet by unplugging the power cord from the tablet.
3.
Disconnect all external devices from the tablet.
4.
Remove the display enclosure (see
Display enclosure
on page
31
).
5.
Disconnect the tablet battery cable from the system board (see
Sensor board
on page
32
).
Remove the solid-state drive:
1.
Remove the Phillips PM1.85×3.00 screw
(1)
that secures the solid-state drive to the system
board.
2.
Lift the side of the solid-state drive
(2)
opposite the slot until it rests at an angle.
44
Chapter 5
Removal and replacement procedures