HP StorageWorks 1606 HP StorageWorks Fabric OS 6.3.0 release notes (5697-0358, - Page 54

Web Tools Switch Admin: QoS: User defined priority group 0-7 does

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Web Tools shows no SFP details for CEE interfaces. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Use the CLI interface. On Enabling LLDP status and assigning FCoE priority bits globally, is Fixed in Fabric OS 6.3.0 not getting reflected in Port Admin window. Confusing error message when copying a source configuration from a remote server. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Do clean-up before downloading a new CEE configuration: 1. In cmsh, run "write erase" to clear startup-config. 2. Reboot switch by running "reboot" on FOS prompt. 3. In cmsh, use "copy" command to copy backup configuration into running-config. Defect ID: DEFECT000247893 Summary: Port Auto Disable - Ports outside of given range are being enabled. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Enable and disable port auto disable for ports one at a time. IPv6 Address dropped from ag --show. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Issue switchdisable/enable causes the IPv6 Address again to be presented. Port statistics details are not getting refreshed for EX ports. Fixed in Fabric OS 6.3.0 Web Tools Switch Admin: QoS: User defined priority group 0-7 does not show up in the drop down for priority group id. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Use CLI to map user defined priority group to a CoS. 8/8 or 8/16 returned invalid value for 'swFCPortFlag' MIB object from 8/8 or 8/16 on SNMP manager. Fixed in Fabric OS 6.3.0 MAC learning/flushing times are very slow on 2408 FCoE CN Switch Fixed in Fabric OS 6.3.0 Switch. Switch crashed on sending LOGO from Finisar LT. Fixed in Fabric OS 6.3.0 Virtual Fabrics 6.2.0c when XISL use is enabled base logical switch in switchshow shows Allow XISL Use as "off" open RFE 1249. Modify fipcfg --advintvl cli to reject non-zero values for FKA interval. Fixed in Fabric OS 6.3.0 Fixed in Fabric OS 6.3.0 CUP needs to send an RSCN after coming back online after a cold boot. Fixed in Fabric OS 6.3.0 WT: FCoE connected devices tab, sort order of Device WWN is incor- Fixed in Fabric OS 6.3.0 rect. In an FCR environment, switch runs out of memory when connected with EoS switches. Fixed in Fabric OS 6.3.0 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Use the CLI interface.
Web Tools shows no SFP details for CEE interfaces.
Fixed in Fabric OS 6.3.0
On Enabling LLDP status and assigning FCoE priority bits globally, is
not getting reflected in Port Admin window.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Do clean-up before downloading a
new CEE configuration: 1. In cmsh,
run "write erase" to clear
startup-config. 2. Reboot switch by
running "reboot" on FOS prompt. 3.
In cmsh, use "copy" command to
copy backup configuration into
running-config.
Confusing error message when copying a source configuration from
a remote server.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Enable and disable port auto disable
for ports one at a time.
Defect ID: DEFECT000247893 Summary: Port Auto Disable - Ports
outside of given range are being enabled.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Issue switchdisable/enable causes the
IPv6 Address again to be presented.
IPv6 Address dropped from ag --show.
Fixed in Fabric OS 6.3.0
Port statistics details are not getting refreshed for EX ports.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Use CLI to map user defined priority
group to a CoS.
Web Tools Switch Admin: QoS: User defined priority group 0-7 does
not show up in the drop down for priority group id.
Fixed in Fabric OS 6.3.0
8/8 or 8/16 returned invalid value for 'swFCPortFlag' MIB object
from 8/8 or 8/16 on SNMP manager.
Fixed in Fabric OS 6.3.0
MAC learning/flushing times are very slow on 2408 FCoE CN Switch
Switch.
Fixed in Fabric OS 6.3.0
Switch crashed on sending LOGO from Finisar LT.
Fixed in Fabric OS 6.3.0
Virtual Fabrics 6.2.0c when XISL use is enabled base logical switch
in switchshow shows Allow XISL Use as "off" open RFE 1249.
Fixed in Fabric OS 6.3.0
Modify fipcfg --advintvl cli to reject non-zero values for FKA interval.
Fixed in Fabric OS 6.3.0
CUP needs to send an RSCN after coming back online after a cold
boot.
Fixed in Fabric OS 6.3.0
WT: FCoE connected devices tab, sort order of Device WWN is incor-
rect.
Fixed in Fabric OS 6.3.0
In an FCR environment, switch runs out of memory when connected
with EoS switches.
54