HP StorageWorks 1606 HP StorageWorks Fabric OS 6.3.0 release notes (5697-0358, - Page 61

Optimized SERDES setting for Brocade 8Gb SAN Switch

Get HP StorageWorks 1606 - Extension SAN Switch PDF manuals and user guides View all HP StorageWorks 1606 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Sequence of creating two TI zones, not saving the change and then modifying the attributes with the "zone --add" command results in misconfigured attributes that will cause software verify on remote switches when changes are commited. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Other methods of creating TI Zones and modifying the definitions work seamlessly. Its just this odd set of steps which produce the failing condition. When creating multiple TI zones, they should be saved before modifying the attributes. Can clean up problem by using zone --add to modify the attributes again after the save. Can also delete and recreate TI zone. Specific call to CEE library results in gradual memory leak. Fixed in Fabric OS 6.3.0 Getting ms_ficon errors on console of core DC SAN Director in McDATA interop after reboots. Fixed in Fabric OS 6.3.0 Configdownload fails with Lsan tag download failed: Duplicate tag. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Use CLI to add the tag names back onto the FCR switch. In Interopmode 2 mode, FC address is shown without offset in switch.html and portshow (cli), but shown with offset in switchshow. Fixed in Fabric OS 6.3.0 Ipaddrset command to set Lance GE ports IP address is non-responsive. Must reboot active CP to activate IP. Fixed in Fabric OS 6.3.0 Workaround prior to code change: The following should work. Following any removal or relocation of an encryption blade from any chassis slot, do an hafailover to cause the standby CP to become active. This should be done even if no change in chassis IP addresses is required as other problems could be otherwise encountered, depending on network configuration. Optimized SERDES setting for Brocade 8Gb SAN Switch for BladeSystem c-Class. If TI zone operations are performed simultaneously on different switches, active CP may failover due to termination of Name server module. Fixed in Fabric OS 6.3.0 Fixed in Fabric OS 6.3.0 Workaround prior to code change: No workaround needed, the DC SAN Director CP fails over non-disruptively and retains all configuration data. 4Gb switch running at fixed 2Gb speed may not respond to FLOGI from HBA using auto-speed negotiation. Fixed in Fabric OS 6.3.0 Workaround prior to code change: Lock the port to fixed speed. HP StorageWorks Fabric OS 6.3.0 release notes 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Other methods of creating TI Zones
and modifying the definitions work
seamlessly. Its just this odd set of steps
which produce the failing condition.
When creating multiple TI zones, they
should be saved before modifying the
attributes. Can clean up problem by
using zone --add to modify the
attributes again after the save. Can
also delete and recreate TI zone.
Sequence of creating two TI zones, not saving the change and then
modifying the attributes with the "zone --add" command results in
misconfigured attributes that will cause software verify on remote
switches when changes are commited.
Fixed in Fabric OS 6.3.0
Specific call to CEE library results in gradual memory leak.
Fixed in Fabric OS 6.3.0
Getting ms_ficon errors on console of core DC SAN Director in
McDATA interop after reboots.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Use CLI to add the tag names back
onto the FCR switch.
Configdownload fails with Lsan tag download failed: Duplicate tag.
Fixed in Fabric OS 6.3.0
In Interopmode 2 mode, FC address is shown without offset in
switch.html and portshow (cli), but shown with offset in switchshow.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
The following should work. Following
any removal or relocation of an
encryption blade from any chassis
slot, do an hafailover to cause the
standby CP to become active. This
should be done even if no change in
chassis IP addresses is required as
other problems could be otherwise
encountered, depending on network
configuration.
Ipaddrset command to set Lance GE ports IP address is non-responsive.
Must reboot active CP to activate IP.
Fixed in Fabric OS 6.3.0
Optimized SERDES setting for Brocade 8Gb SAN Switch for
BladeSystem c-Class.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
No workaround needed, the DC SAN
Director CP fails over non-disruptively
and retains all configuration data.
If TI zone operations are performed simultaneously on different
switches, active CP may failover due to termination of Name server
module.
Fixed in Fabric OS 6.3.0
Workaround prior to code change:
Lock the port to fixed speed.
4Gb switch running at fixed 2Gb speed may not respond to FLOGI
from HBA using auto-speed negotiation.
HP StorageWorks Fabric OS 6.3.0 release notes
61