HP dx2290 Service Reference Guide - HP Compaq dx2290 Business PC - Page 49

Removing the diskette or hard disk drive, Preparation for Disassembly, on Access Panel

Get HP dx2290 - Microtower PC PDF manuals and user guides View all HP dx2290 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Removing the diskette or hard disk drive NOTE: On some models, the primary hard disk drive is located in the internal 3.5-inch drive cage. On other models, the primary hard disk drive is located in the external 3.5-inch drive bay as shown here. 1. Prepare the computer for disassembly (Preparation for Disassembly on page 26). 2. Remove the access panel (Access Panel on page 28). 3. Remove the front bezel (Front Bezel on page 29). 4. Release the diskette (floppy) or hard disk drive by removing the two screws on the side of the drive, and then slide the drive part way out of the front of the chassis. 5. Disconnect the power and data cables from the back of the drive. 2 1 6. Pull the drive out through the front of the chassis. To replace the diskette or hard disk drive, reverse the removal procedures. Removing and replacing drives 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Removing the diskette or hard disk drive
NOTE:
On some models, the primary hard disk drive is located in the internal 3.5-inch drive cage. On
other models, the primary hard disk drive is located in the external 3.5-inch drive bay as shown here.
1.
Prepare the computer for disassembly (
Preparation for Disassembly
on page
26
).
2.
Remove the access panel (
Access Panel
on page
28
).
3.
Remove the front bezel (
Front Bezel
on page
29
).
4.
Release the diskette (floppy) or hard disk drive by removing the two screws on the side of the drive,
and then slide the drive part way out of the front of the chassis.
5.
Disconnect the power and data cables from the back of the drive.
1
2
6.
Pull the drive out through the front of the chassis.
To replace the diskette or hard disk drive, reverse the removal procedures.
Removing and replacing drives
41