HP dx2290 Service Reference Guide - HP Compaq dx2290 Business PC - Page 53

Adding or replacing a hard disk drive, If you are replacing an old drive with a new drive

Get HP dx2290 - Microtower PC PDF manuals and user guides View all HP dx2290 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Adding or replacing a hard disk drive NOTE: On some models, the primary hard disk drive is located in the internal 3.5-inch drive cage as shown in this section. On other models, the primary hard disk drive is located in the external 3.5-inch drive bay. 1. If necessary, remove the existing drive. See Removing the hard disk drive on page 43. 2. Slide the new drive into the hard disk drive cage, aligning the drive with the four screw holes on the cage. Install the four screws that secure the hard disk drive to the hard disk drive cage. Make sure the hard disk drive cables are facing the top of the drive cage. NOTE: If you are replacing an old drive with a new drive, remove the four guide screws from the old drive, and use the screws to install the new drive. 3. Place the hard disk drive cage into the chassis. The two screw holes on the hard disk drive cage (A) should be aligned with the screw holes on the chassis (B). Removing and replacing drives 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Adding or replacing a hard disk drive
NOTE:
On some models, the primary hard disk drive is located in the internal 3.5-inch drive cage as
shown in this section. On other models, the primary hard disk drive is located in the external 3.5-inch
drive bay.
1.
If necessary, remove the existing drive. See
Removing the hard disk drive
on page
43
.
2.
Slide the new drive into the hard disk drive cage, aligning the drive with the four screw holes on
the cage. Install the four screws that secure the hard disk drive to the hard disk drive cage. Make
sure the hard disk drive cables are facing the top of the drive cage.
NOTE:
If you are replacing an old drive with a new drive, remove the four guide screws from the
old drive, and use the screws to install the new drive.
3.
Place the hard disk drive cage into the chassis. The two screw holes on the hard disk drive
cage
(A)
should be aligned with the screw holes on the chassis
(B)
.
Removing and replacing drives
45