Husqvarna 562 XP G Workshop Manual - Page 29

Assembling the ignition module and, flywheel

Get Husqvarna 562 XP G PDF manuals and user guides View all Husqvarna 562 XP G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

7.7 Assembling the ignition module and flywheel 1 Run the cables through the opening in the crankcase. Screw the earth cable in place. See figure 11. Fit the cabling to the stop button. 2 Position the cable channel as outlined in figure 10. NOTE! Take care that the cable channel is positioned correctly under the ignition module so that the cables are not crushed. 3 Place the ignition module in position. See figure 13. Do not tighten the screws. Fig 11 4 Fit the flywheel onto the crankshaft pin. Turn the flywheel until the key fits into the key slot on the shaft. See figure 12. Tighten the screw for the flywheel. Fig 12 5 Insert the plastic air gap tool, at a thickness of 0.3 +- 0.1 mm, between the lugs on the ignition module and flywheel. Turn the flywheel so that the magnets are positioned opposite the ignition module. Tighten the screws, at a tightening torque of 4.5- 6 Nm. Remove the plastic air gap tool. Fit the intake system as outlined in "7.14 Assembling the intake system", the tank unit as outlined in "7.16 tank unit", and the air filter as outlined in "Assembling the carburettor". 6 Press the ignition lead into the holder on the partition wall. 7 Then fit: • The air nozzle • The guide rail and press the cable in place • the spark plug hat by unscrewing the piston stop. • The starter, at a tightening torque of 2.5-3.5 Nm • The cylinder cover Fig 13 Repair Instructions English - 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
English -
29
Repair Instructions
7.7 Assembling the ignition module and
flywheel
1
Run the cables through the opening in the crank-
case. Screw the earth cable in place. See figure 11.
Fit the cabling to the stop button.
2
Position the cable channel as outlined in figure 10.
NOTE! Take care that the cable channel is posi-
tioned correctly under the ignition module so that
the cables are not crushed.
3
Place the ignition module in position. See figure 13.
Do not tighten the screws.
Fig 12
Fig 13
4
Fit the flywheel onto the crankshaft pin. Turn the
flywheel until the key fits into the key slot on the
shaft. See figure 12.
Tighten the screw for the flywheel.
5
Insert the plastic air gap tool, at a thickness of
0.3 +- 0.1 mm, between the lugs on the ignition
module and flywheel. Turn the flywheel so that the
magnets are positioned opposite the ignition mod-
ule. Tighten the screws, at a tightening torque of
4.5- 6 Nm. Remove the plastic air gap tool. Fit the
intake system as outlined in “7.14 Assembling the
intake system”, the tank unit as outlined in “7.16
tank unit”, and the air filter as outlined in “Assem-
bling the carburettor”.
6
Press the ignition lead into the holder on the parti-
tion wall.
7
Then fit:
•
The air nozzle
•
The guide rail and press the cable in place
•
the spark plug hat by unscrewing the piston stop.
•
The starter, at a tightening torque of 2.5-3.5 Nm
•
The cylinder cover
Fig 11