Husqvarna 562 XP G Workshop Manual - Page 49

Dismantling the crankshaft and, crankcase

Get Husqvarna 562 XP G PDF manuals and user guides View all Husqvarna 562 XP G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

7.24 Dismantling the crankshaft and crankcase 1 Dismantle the following: • The clutch cover • The chain and bar. • The centrifugal clutch * • The cylinder cover • The starter * • The flywheel * • The carburettor * • The bottom of the carburettor * • The hand guard * • The muffler * • The handle system * • The fuel unit * • The piston and cylinder * • The ignition module • Cabling • The oil pump * See specific instruction. Fig 69 NOTE! Take care to prevent any dirt and foreign particles from entering the bearings. 2. If required, remove the circlip on the flywheel side. 3. Remove the 5 screws from the pulley wheel side. See Figure 69. 4. Fit tool 575 28 69-01 as outlined in figure 70. Remove the crankcase half on the clutch side. 5. Fit tool575 28 69-01 as outlined in figure 71. Remove the flywheel side's crankcase half. 6. Carefully pull the crankcase halves apart. Two guide pins keep the crankcase halves together. Lift out the connecting rod and dispose of the gasket. Fig 70 WARNING! Beware of burn injuries as the crankcase halves are hot. Wear protective gloves. Fig 71 Repair Instructions x4 English - 49

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
English -
49
Repair Instructions
7.24 Dismantling the crankshaft and
crankcase
1
Dismantle the following:
•
The clutch cover
•
The chain and bar.
•
The centrifugal clutch *
• The cylinder cover
• The starter *
•
The flywheel *
• The carburettor *
•
The bottom of the carburettor *
•
The hand guard *
• The muffler *
•
The handle system *
•
The fuel unit *
•
The piston and cylinder *
•
The ignition module
•
Cabling
•
The oil pump
* See specific instruction.
x4
Fig 69
Fig 70
Fig 71
NOTE!
Take care to prevent any dirt and foreign
particles from entering the bearings.
2.
If required, remove the circlip on the flywheel side.
3.
Remove the 5 screws from the pulley wheel side.
See Figure 69.
4.
Fit tool 575 28 69-01 as outlined in figure 70.
Remove the crankcase half on the clutch side.
5.
Fit tool575 28 69-01 as outlined in figure 71.
Remove the flywheel side’s crankcase half.
6.
Carefully pull the crankcase halves apart. Two
guide pins keep the crankcase halves together. Lift
out the connecting rod and dispose of the gasket.
WARNING!
Beware of burn injuries as the crankcase
halves are hot. Wear protective gloves.