Husqvarna 562 XP G Workshop Manual - Page 52

H. Bar and chain. See the Operator's Manual.

Get Husqvarna 562 XP G PDF manuals and user guides View all Husqvarna 562 XP G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Repair Instructions 8 Assemble the following parts: A. Tank unit. See page 43. B. Piston and cylinder. See page 47. C. Muffler. See page 19. D. Carburettor. See page 40. E. Centrifugal clutch. See page 31. F. Electrical System. See page 29. G. Starter. See page 25. H. Bar and chain. See the Operator's Manual. Sealing rings 1 To replace the crankshaft's sealing rings, first dismantle the following parts: On the flywheel side: • Starter. See page 25. • Flywheel. See page 28. On the clutch side: • Bar and chain. See the Operator's Manual. • Chain guide plate. See page 17. • Centrifugal clutch. See page 30. • Oil pump. See page 31. 2 Use a screwdriver to remove the sealing ring and pull it out. 3 Slide the dowel 575 34 69-01 (figure 80) on the crankcase pin. Knock the new sealing ring in place using the 575 34 70-01 tool. See Figure 81. 4 Fit the parts as outlined in point 1 above. Fig 80 52 - English Fig 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
52
- English
Fig 80
Fig 81
8
Assemble the following parts:
A. Tank unit. See page 43.
B. Piston and cylinder. See page 47.
C. Muffler. See page 19.
D. Carburettor. See page 40.
E. Centrifugal clutch. See page 31.
F.
Electrical System. See page 29.
G. Starter. See page 25.
H. Bar and chain. See the Operator’s Manual.
Sealing rings
1
To replace the crankshaft’s sealing rings, first dis-
mantle the following parts:
On the flywheel side:
•
Starter. See page 25.
•
Flywheel. See page 28.
On the clutch side:
•
Bar and chain. See the Operator’s Manual.
•
Chain guide plate. See page 17.
•
Centrifugal clutch. See page 30.
•
Oil pump. See page 31.
2
Use a screwdriver to remove the sealing ring and
pull it out.
3
Slide the dowel 575 34 69-01 (figure 80) on the
crankcase pin. Knock the new sealing ring in place
using the 575 34 70-01 tool. See Figure 81.
4
Fit the parts as outlined in point 1 above.
Repair Instructions