IBM 79856au Installation Guide - Page 39

Installing, riser-card, assembly

Get IBM 79856au - Servers System X3655 Opteron 2.8ghz PDF manuals and user guides
UPC - 883436004374
View all IBM 79856au manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Installing the riser-card assembly To install the riser-card assembly, complete the following steps: Access holes Release tabs 1. Read the safety information that begins on page v and "Installation guidelines" on page 9. 2. Make sure that the server and all peripheral devices are turned off, and that the power cords and all external cables are disconnected. 3. Reinstall the Remote Supervisor Adapter II SlimLine if you removed it. 4. Reinstall any adapters and reconnect any cables you might have removed in other procedures. 5. Carefully align the riser-card assembly with the retention latches, the guides on the rear of the server, and the riser-card connector on the system board; then, press down on the assembly. Make sure that the riser-card assembly is fully seated in the riser-card connector on the system board. If you have other devices to install, do so now. Otherwise, go to "Completing the installation" on page 29. Chapter 2. Installing optional devices 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
Installing
the
riser-card
assembly
To
install
the
riser-card
assembly,
complete
the
following
steps:
Access holes
Release tabs
1.
Read
the
safety
information
that
begins
on
page
v
and
“Installation
guidelines”
on
page
9.
2.
Make
sure
that
the
server
and
all
peripheral
devices
are
turned
off,
and
that
the
power
cords
and
all
external
cables
are
disconnected.
3.
Reinstall
the
Remote
Supervisor
Adapter
II
SlimLine
if
you
removed
it.
4.
Reinstall
any
adapters
and
reconnect
any
cables
you
might
have
removed
in
other
procedures.
5.
Carefully
align
the
riser-card
assembly
with
the
retention
latches,
the
guides
on
the
rear
of
the
server,
and
the
riser-card
connector
on
the
system
board;
then,
press
down
on
the
assembly.
Make
sure
that
the
riser-card
assembly
is
fully
seated
in
the
riser-card
connector
on
the
system
board.
If
you
have
other
devices
to
install,
do
so
now.
Otherwise,
go
to
“Completing
the
installation”
on
page
29.
Chapter
2.
Installing
optional
devices
25