Icom IC-M424G Instruction Manual - Page 18

Entering the, ATIS code, For Dutch and German version transceivers

Get Icom IC-M424G PDF manuals and user guides View all Icom IC-M424G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

3 PREPARATION ■■Entering the ATIS code (For Dutch and German version transceivers) The 10 digit ATIS (Automatic Transmitter Identification System) code can be entered at power ON. This initial code setting can be made only once. After being set, it can be changed by only your dealer or distributor. If your ATIS code has already been entered, the following steps are not necessary. rrRepeat step e to enter all 10 digits. ttAfter entering the 10 digit code, "FINISH" is automatically selected, and then push [ENT] or Dial to set it. yyThe "ATIS CONFIRMATION" screen is displayed. qqAfter entered the MMSI code, "Push [ENT] to Register Your ATIS" is displayed. wwPush [ENT] to start entering the ATIS code. • Push [CLEAR] twice to cancel the entry, and go to the normal operating mode. In this case, the ATIS function is disabled. To enter the ATIS code, turn OFF the power, then turn it ON again. eeEnter your ATIS code in the following manner: • Select a desired number using Dial, or Push [ENT] or Dial to set it. • T o move the cursor, select either arrow, "←" or "→," then push [ENT] or Dial. uuEnter your ATIS code again for confirmation. • Enter in the same manner as steps e through t. iiWhen your ATIS code is successfully entered, the screen as shown below is briefly displayed. • After that, the normal operating screen is displayed. The entered ATIS code can be checked in the MENU screen. (p. 69) 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
8
3
PREPARATION
The 10 digit ATIS (Automatic Transmitter Identification Sys-
tem) code can be entered at power ON.
This initial code setting can be made only once.
After being set, it can be changed by only your dealer
or distributor. If your ATIS code has already been en-
tered, the following steps are not necessary.
After entered the MMSI code, “Push [ENT] to Register
q
Your ATIS” is displayed.
Push [ENT] to start entering the ATIS code.
w
• Push [CLEAR] twice to cancel the entry, and go to the normal
operating mode. In this case, the ATIS function is disabled. To
enter the ATIS code, turn OFF the power, then turn it ON again.
Enter your ATIS code in the following manner:
e
• Select a desired number using Dial, or [
∫
]/[
√
]/[
Ω
]/[
≈
].
• Push [ENT] or Dial to set it.
•To move the cursor, select either arrow, “
←
” or “
→
,” then push
[ENT] or Dial.
Repeat step
r
e
to enter all 10 digits.
After entering the 10 digit code, “FINISH” is automatically
t
selected, and then push [ENT] or Dial to set it.
The “ATIS CONFIRMATION” screen is displayed.
y
Enter your ATIS code again for confirmation.
u
• Enter in the same manner as steps
e
through
t
.
When your ATIS code is successfully entered, the screen
i
as shown below is briefly displayed.
• After that, the normal operating screen is displayed.
The entered ATIS code can be checked in the MENU screen.
(p. 69)
Entering the
■
ATIS code
(For Dutch and German version transceivers)