Icom IC-M424G Instruction Manual - Page 7

Precautions, Warning! Never, Do Not, Be Careful

Get Icom IC-M424G PDF manuals and user guides View all Icom IC-M424G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

PRECAUTIONS RWARNING! NEVER connect the transceiver to an AC outlet. This may pose a fire hazard or result in an electric shock. RWARNING! NEVER connect the transceiver to a pow- er source of more than 16 V DC such as a 24 V DC. This could cause a fire or damage the transceiver. RWARNING! NEVER reverse the DC power cable po- larity when connecting to a power source. This could damage the transceiver. RWARNING! NEVER cut the DC power cable between the DC plug at the back of the transceiver and fuse holder. If an incorrect connection is made after cutting, the transceiver may be damaged. CAUTION: NEVER place the transceiver where normal operation of the vessel may be hindered or where it could cause bodily injury. KEEP the transceiver and microphone at least 1 m away from the vessel's magnetic navigation compass. DO NOT use or place the transceiver in areas with tem- peratures below -20°C (-4°F) or above +60°C (+140°F) or, in areas subject to direct sunlight, such as the dashboard. 1 2 DO NOT use harsh solvents such as benzine or alcohol to clean the transceiver, as they will damage the transceiver's 3 surfaces. If the transceiver becomes dusty or dirty, wipe it 4 clean with a soft, dry cloth. DO NOT disassemble or modify the transceiver for any rea- 5 son. 6 BE CAREFUL! The transceiver rear panel will become 7 hot when operating continuously for long periods of time. 8 Place the transceiver in a secure place to avoid inadvertent 9 use by children. 10 BE CAREFUL! The transceiver meets IPX7* requirements 11 for waterproof protection. However, once the transceiver has been dropped, waterproof protection cannot be guaranteed 12 because of possible damage to the transceiver's case or the 13 waterproof seal. * Except for the DC power connector, NMEA In/Out leads and AF 14 Out leads. 15 For U.S.A. only 16 CAUTION: Changes or modifications to this device, not ex- pressly approved by Icom Inc., could void your authority to operate this device under FCC regulations. vi

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
vi
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
PRECAUTIONS
R
WARNING! NEVER
connect the transceiver to an AC
outlet. This may pose a fire hazard or result in an electric shock.
R
WARNING! NEVER
connect the transceiver to a pow-
er source of more than 16 V DC such as a 24 V DC. This
could cause a fire or damage the transceiver.
R
WARNING! NEVER
reverse the DC power cable po-
larity when connecting to a power source. This could damage
the transceiver.
R
WARNING! NEVER
cut the DC power cable between
the DC plug at the back of the transceiver and fuse holder. If
an incorrect connection is made after cutting, the transceiver
may be damaged.
CAUTION: NEVER
place the transceiver where normal
operation of the vessel may be hindered or where it could
cause bodily injury.
KEEP
the transceiver and microphone at least 1 m away
from the vessel’s magnetic navigation compass.
DO NOT
use or place the transceiver in areas with tem-
peratures below –20°C (–4°F) or above +60°C (+140°F) or, in
areas subject to direct sunlight, such as the dashboard.
DO NOT
use harsh solvents such as benzine or alcohol to
clean the transceiver, as they will damage the transceiver’s
surfaces. If the transceiver becomes dusty or dirty, wipe it
clean with a soft, dry cloth.
DO NOT
disassemble or modify the transceiver for any rea-
son.
BE CAREFUL!
The transceiver rear panel will become
hot when operating continuously for long periods of time.
Place the transceiver in a secure place to avoid inadvertent
use by children.
BE CAREFUL!
The transceiver meets IPX7
*
requirements
for waterproof protection. However, once the transceiver has
been dropped, waterproof protection cannot be guaranteed
because of possible damage to the transceiver’s case or the
waterproof seal.
* Except for the DC power connector, NMEA In/Out leads and AF
Out leads.
For U.S.A. only
CAUTION:
Changes or modifications to this device, not ex-
pressly approved by Icom Inc., could void your authority to
operate this device under FCC regulations.