JVC DLA-NX5 Operation Manual 1 - Page 71

Troubleshooting

Get JVC DLA-NX5 PDF manuals and user guides View all JVC DLA-NX5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Troubleshooting Before sending the unit to your authorized dealer for repair, please check the following points. The following symptoms are not malfunctions. You do not need to worry about the following symptoms if there is no abnormality on the screen. 0 A part of the top or front surface of the unit is hot. 0 A creaking sound is heard from the unit. 0 An operating sound is heard from the inside of the unit. 0 Color smear occurs on some screens. This unit is a digital device. This unit may become unable to operate normally due to external static or noise. Perform the following operations when such malfunctions occur. A If the unit is in the Standby mode, pull out the power plug, followed by inserting it again B Press the A button on the projector unit to turn on the power again When "High Altitude Mode" is set to "On", and "Lamp Power" is set to "High" during 3D mode, the fan will make louder noise than usual since it is designed to run at high speed in 3D mode. Power is not supplied Check Is the power cord disconnected? Is the lamp cover properly shut? Is the unit in the Cool-down mode? Is the unit in the Eco mode? Action Refer to Insert the power cord (plug) firmly. P. 21 If the unit is in the Standby mode, remove the power plug P. 67 and close the lamp cover properly. After that, insert the plug again. After exiting the Cool-down mode, turn on the power again. P. 23 Press the A button on the projector unit or the remote P. 64 control unit. After the "STANDBY/ON" indicator lights up in red, press the C [ON] button. Power shuts down automatically Check Action Has "ECO Mode" been configured? Set "ECO Mode" to "Off". Has "Off Timer" been configured? Set "Off Timer" to "Off". Are the air inlets and exhaust vent blocked? Leave proper clearance when installing the unit. Is there a large amount of dirt attached to Remove the dirt using a vacuum cleaner. the sponge filter? Refer to P. 64 P. 64 P. 11, 16 P. 70 Troubleshooting 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
Troubleshooting
Before sending the unit to your authorized dealer for repair, please check the following points.
The following symptoms are not malfunctions.
You do not need to worry about the following symptoms if there is no abnormality on the screen.
0
A part of the top or front surface of the unit is hot.
0
A creaking sound is heard from the unit.
0
An operating sound is heard from the inside of the unit.
0
Color smear occurs on some screens.
This unit is a digital device. This unit may become unable to operate normally due to external static or noise.
Perform the following operations when such malfunctions occur.
A
If the unit is in the Standby mode, pull out the power plug, followed by inserting it again
B
Press the
A
button on the projector unit to turn on the power again
When “High Altitude Mode” is set to “On”, and “Lamp Power” is set to “High” during 3D mode, the fan will
make louder noise than usual since it is designed to run at high speed in 3D mode.
Power is not supplied
Check
Action
Refer to
Is the power cord disconnected?
Insert the power cord (plug) firmly.
P. 21
Is the lamp cover properly shut?
If the unit is in the Standby mode, remove the power plug
and close the lamp cover properly. After that, insert the plug
again.
P. 67
Is the unit in the Cool-down mode?
After exiting the Cool-down mode, turn on the power again.
P. 23
Is the unit in the Eco mode?
Press the
A
button on the projector unit or the remote
control unit. After the “STANDBY/ON” indicator lights up in
red, press the
C
[ON] button.
P. 64
Power shuts down automatically
Check
Action
Refer to
Has “ECO Mode” been configured?
Set “ECO Mode” to “Off”.
P. 64
Has “Off Timer” been configured?
Set “Off Timer” to “Off”.
P. 64
Are the air inlets and exhaust vent
blocked?
Leave proper clearance when installing the unit.
P. 11, 16
Is there a large amount of dirt attached to
the sponge filter?
Remove the dirt using a vacuum cleaner.
P. 70
71
Troubleshooting