Kyocera TASKalfa 4551ci Printing System (11),(12),(13),(14) Color Printing Gu - Page 47

Adding custom calibration sets, Adding custom calibration sets and output profiles

Get Kyocera TASKalfa 4551ci PDF manuals and user guides View all Kyocera TASKalfa 4551ci manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

CALIBRATION 47 Adding custom calibration sets If you are printing on a paper that is similar to the recommended paper but uses different print settings, you might still be able to use the output profile, but you must create a custom calibration set. If the color quality is sufficient, you do not need to create a custom profile (see scenario 3 in the table under "Using the output profiles and calibration sets" on page 45). You can add a new calibration set that you can then select when performing calibration. You can delete a custom calibration set. You cannot delete a factory-supplied calibration set. For instructions on adding a custom calibration set, see Command WorkStation Help. Adding custom calibration sets and output profiles If you determine that none of the factory-supplied output profiles yields acceptable color with your paper, you must create a custom calibration set in Calibrator and a custom profile using profile-generating software such as Fiery Color Profiler Suite (see scenario 4 in the table under "Using the output profiles and calibration sets" on page 45). NOTE: Before creating a custom calibration set and custom output profile, make sure that the copier is calibrated (if calibration is supported on the copier). For information about performing copier calibration, see the documentation that accompanies the copier. Calibration on the E100 requires that each output profile contains a calibration target. If you use Fiery Color Profiler Suite to create a custom output profile, you do not have to perform any procedures to add a calibration target to the output profile. Color Profiler Suite can create a profile that contains a calibration target. • First, create a custom calibration set using Calibrator in Command WorkStation. • Next, create a custom output profile using Color Profiler Suite and install it on the E100.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
C
ALIBRATION
47
Adding custom calibration sets
If you are printing on a paper that is similar to the recommended paper but uses different
print settings, you might still be able to use the output profile, but you must create a custom
calibration set. If the color quality is sufficient, you do not need to create a custom profile (see
scenario 3 in the table under
“Using the output profiles and calibration sets”
on page 45).
You can add a new calibration set that you can then select when performing calibration. You
can delete a custom calibration set. You cannot delete a factory-supplied calibration set.
For instructions on adding a custom calibration set, see Command WorkStation Help.
Adding custom calibration sets and output profiles
If you determine that none of the factory-supplied output profiles yields acceptable color with
your paper, you must create a custom calibration set in Calibrator and a custom profile using
profile-generating software such as Fiery Color Profiler Suite (see scenario 4 in the table under
“Using the output profiles and calibration sets”
on page 45).
N
OTE
:
Before creating a custom calibration set and custom output profile, make sure that the
copier is calibrated (if calibration is supported on the copier). For information about
performing copier calibration, see the documentation that accompanies the copier.
Calibration on the E100 requires that each output profile contains a calibration target. If you
use Fiery Color Profiler Suite to create a custom output profile, you do not have to perform
any procedures to add a calibration target to the output profile. Color Profiler Suite can create
a profile that contains a calibration target.
•
First, create a custom calibration set using Calibrator in Command WorkStation.
•
Next, create a custom output profile using Color Profiler Suite and install it on the E100.