Lenovo PC 300GL Using your Personal Computer - PC300GL - 6561, 6591 - Page 85

configuration in the Configuration/Setup Utility Program.

Get Lenovo PC 300GL PDF manuals and user guides View all Lenovo PC 300GL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

POST Message 164 167 175 Description A change in the memory configuration occurred. This error can be caused by adding, removing, or incorrectly installing memory. Note: The computer can be used with decreased memory capacity until the error is corrected. Action: 1. If you added memory, see Installing Options in Your Personal Computer and Chapter 4, "Configuring Your Computer" on page 39 of this booklet to verify that the new memory is correct for your computer, and that it is installed and configured correctly. 2. If you added or removed memory, you must save the new configuration in the Configuration/Setup Utility Program. Refer to the Important text box on page 40 for further information and instructions on saving the configuration. 3. Running the diagnostic programs might isolate the location of the problem DIMM and provide additional information. (See "Diagnostic Programs" on page 97 for information about diagnostic programs provided with your computer.) If the problem cannot be isolated and corrected, have the computer serviced. The microprocessor was updated and the correct system BIOS update program was not found. This error can be caused when a different microprocessor is installed. Action: If you updated the microprocessor, refer to "Updating the System BIOS" on page 33 and perform the BIOS flash update procedure. If the problem cannot be isolated and corrected, have the computer serviced. The primary copy of secure data is damaged. This can occur if the computer is turned off while the Configuration/Setup Utility program is updating the administrator password or startup sequence. Action: POST will attempt to use the alternate copy of secure data to correct the primary copy. If the operation is successful, the administrator password and startup sequence will remain as they were before the Configuration/Setup Utility program was invoked and this error will not appear during the next power-on. If the operation is not successful, other POST errors might appear and the system board must be replaced. Chapter 6. Solving Problems 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
POST Message
Description
164
A change in the memory configuration occurred.
This error can be
caused by adding, removing, or incorrectly installing memory.
Note:
The computer can be used with decreased memory capacity
until the error is corrected.
Action:
1.
If you added memory, see
Installing Options in Your Personal
Computer
and Chapter
4, “Configuring Your Computer” on
page
39 of this booklet to verify that the new memory is
correct for your computer, and that it is installed and
configured correctly.
2.
If you added or removed memory, you must save the new
configuration in the Configuration/Setup Utility Program.
Refer to the
Important
text box on page 40 for further
information and instructions on saving the configuration.
3.
Running the diagnostic programs might isolate the location of
the problem DIMM and provide additional information.
(See
“Diagnostic Programs” on page
97 for information about
diagnostic programs provided with your computer.)
If the problem cannot be isolated and corrected, have the computer
serviced.
167
The microprocessor was updated and the correct system BIOS
update program was not found.
This error can be caused when a
different microprocessor is installed.
Action:
If you updated the microprocessor,
refer to “Updating
the System BIOS” on page
33 and perform the BIOS flash update
procedure.
If the problem cannot be isolated and corrected, have the computer
serviced.
175
The primary copy of secure data is damaged.
This can occur if the
computer is turned off while the Configuration/Setup Utility
program is updating the administrator password or startup
sequence.
Action:
POST will attempt to use the alternate copy of secure
data to correct the primary copy.
If the operation is successful, the
administrator password and startup sequence will remain as they
were before the Configuration/Setup Utility program was invoked
and this error will not appear during the next power-on.
If the
operation is
not
successful, other POST errors might appear and
the system board must be replaced.
Chapter 6.
Solving Problems
71