Lexmark X852E Setup Guide - Page 26

Attaching the scannershelf, Verifying the IP settings - type number

Get Lexmark X852E - Mfp PDF manuals and user guides
UPC - 734646002806
View all Lexmark X852E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

3 Press Menu until you see Std Net Setup (or Network 1 Setup or Network 2 Setup), and then press Select. 4 Press Menu until you see TCP/IP, and then press Select. 5 Press Menu until you see Set IP Address, and then press Select. 6 Change the address by pressing Menu to increase or decrease each number. Press Select to move to the next segment. Press Select when you are finished. The message Saved appears briefly. 7 Press Menu until you see Set IP Netmask, and then press Select. 8 Repeat step 6 to set the IP Netmask. 9 Press Menu until you see Set IP Gateway, and then press Select. 10 Repeat step 6 to set the IP Gateway. 11 When you are finished, press Go to return the printer to the Ready state. Verifying the IP settings Note: On Windows computers, click Start Programs Command prompt (or Accessories Command prompt if using Windows 2000). 1 Print another network setup page. Look under the "TCP/IP" heading and make sure the IP address, netmask, and gateway are what you expected. See "Printing a network setup page" on page 20 if you need help. 2 Ping the printer and verify that it responds. For example, at a command prompt on a network computer type ping followed by the new printer IP address (for example, 192.168.0.11): ping xxx.xxx.x.xx If the printer is active on the network, you receive a reply. Attaching the scanner shelf 1 Turn the printer off. 2 Unplug the 16 AWG power cord or printer power cord from the grounded outlet. Set up the printer 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
21
Set up the printer
3
Press
Menu
until you see Std Net Setup (or Network 1 Setup or
Network 2 Setup), and then press
Select
.
4
Press
Menu
until you see TCP/IP, and then press
Select
.
5
Press
Menu
until you see Set IP Address, and then press
Select
.
6
Change the address by pressing
Menu
to increase or decrease
each number. Press
Select
to move to the next segment. Press
Select
when you are finished.
The message
Saved
appears briefly.
7
Press
Menu
until you see Set IP Netmask, and then press
Select
.
8
Repeat step 6 to set the IP Netmask.
9
Press
Menu
until you see Set IP Gateway, and then press
Select
.
10
Repeat step 6 to set the IP Gateway.
11
When you are finished, press
Go
to return the printer to the
Ready state.
Verifying the IP settings
1
Print another network setup page. Look under the
“
TCP/IP
”
heading and make sure the IP address, netmask, and gateway
are what you expected.
See
“
Printing a network setup page
”
on page 20 if you need
help.
Note:
On Windows
computers, click
Start
Programs
Command
prompt (or Accessories
Command prompt if using
Windows 2000).
2
Ping the printer and verify that it responds. For example, at a
command prompt on a network computer type
ping
followed
by the new printer IP address (for example, 192.168.0.11):
ping xxx.xxx.x.xx
If the printer is active on the network, you receive a reply.
Attaching the
scanner shelf
1
Turn the printer off.
2
Unplug the 16 AWG power cord or printer power cord from the
grounded outlet.