Marantz AV8003 AV8003 User Manua - Page 52
Marantz AV8003 Manual
View all Marantz AV8003 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 52 highlights
ENGLISH NAMES AND FUNCTION CONNECTIONS SETUP BASIC OPERATION Note: The same operations performed using the 3/ 4 buttons can be performed using the - TUNE + button of item 002 when the remote controller is in TUNER mode. If tuning does not stop at the desired station, use to the "Manual Tuning" operation. MANUAL TUNING 1. 3. 2. STANDBY POWER ON/OFF INPUT SELECTOR PURE DIRECT M-DAX AV PRE TUNER AV8003 UP HDMI DOWN VOLUME SURROUND MODE AUTO PURE DIRECT PHONES ZONE THX ZONE SPEAKER 7.1CH INPUT SETUP MIC MENU EXIT ENTER BAND T-MODE MEMORY CLEAR TOP M-DAX DISPLAY 3. 3. 2. 2. 4. 4. (Using the unit) 1. Turn the INPUT SELECTOR knob to select "TUNER". 2. Press the BAND button to select either FM or AM. 3. Press the 3 or 4 cursor buttons on the front Panel to select the desired station. (Using the remote controller) 1. Switch the remote controller to TUNER mode. 2. Press the < / > button until 001 is displayed. 3. Press the FM or AM button. 4. Press the 3 or 4 cursor buttons to tune in the deseired station. DIRECT FREQUENCY CALL 3. 3. 2. 2. 4. 5. 1. Switch the remote controller to TUNER mode. 2. Press the < / > button until 001 is displayed. 3. Press the FM or AM button. 4. Press the GUIDE button on the remote controller, display will show "FREQ----". 5. lnput your desired station's, frequency with the ten numbered keypad on the remote controller. 6. The desired station will automatically be tuned. (FM) TUNING MODE (AUTO STEREO OR MONO) AUTO, TUNED, ST T-MODE STANDBY POWER ON/OFF INPUT SELECTOR PURE DIRECT M-DAX AV PRE TUNER AV8003 UP HDMI DOWN VOLUME SURROUND MODE AUTO PURE DIRECT PHONES ZONE THX ZONE SPEAKER 7.1CH INPUT SETUP MIC MENU EXIT ENTER BAND T-MODE MEMORY CLEAR TOP M-DAX DISPLAY 3. 3. 2. 2. In TUNER mode, press the T-MODE button on the remote controller to switch between AUTO STEREO and monaural sound. 1. Switch the remote controller to TUNER mode. 2. Press the < / > button on the remote controller to display 002. 3. Each time the T-MODE button is pressed, the TUNER mode changes and the mode is displayed on the FL display. Analog / Digital Auto Mode T-MODE:DIG-AT For listening to HD Radio stations. See p.52 for more information on HD Radio technology. Analog Auto Mode (when receiving FM broadcasts) T-MODE:ANA-AT AUTO STEREO mode is selected and the AUTO indicator is illuminated on the FL display. When stereo broadcasts are received, the ST indicator is illuminated on the FL display. Note: • This mode is not available when BAND is set to AM. Analog Mono Mode T-MODE:MONO MONO mode is selected and the AUTO indicator disappears from the FL display. Monaural broadcasts are received in TUNER mode. Note: • If the unit receives a weak signal or it is difficult to receive a stereo signal, press the T-MODE button on the remote controller or the unit to switch to MONO mode. This reduces the amount of noise and makes broadcasts easier to hear. The AUTO indicator on the FL display disappears. PRESET MEMORY With this unit you can preset up to 60 FM/AM stations in any order. For each station, you can memorize the frequency and reception mode if desired. AUTO PRESET MEMORY This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory. 2. 4. 1. 3. 2. 5. STANDBY POWER ON/OFF INPUT SELECTOR PURE DIRECT M-DAX AV PRE TUNER AV8003 UP HDMI DOWN VOLUME SURROUND MODE AUTO PURE DIRECT PHONES ZONE THX ZONE SPEAKER 7.1CH INPUT SETUP MIC MENU EXIT ENTER BAND T-MODE MEMORY CLEAR TOP M-DAX DISPLAY 1. To select FM , press the BAND button on the front panel. 2. While pressing the MEMORY button, press the 1 cursor button. "AUTO PRESET" will appear on the display, and scanning starts from the lowest frequency. 3. Each time the tuner finds a station, scanning will pause and the station will be played for five seconds. During this time, the following operations are possible. The band can be changed by the BAND button. 4. If no button is pressed during this period, the current station is memorized in location Preset 02. If you wish to skip the current station, press the 3 cursor button during this period, this station is skipped and auto presetting continues. 5. Operation stops automatically when all 60 preset memory positions are filled or when auto scanning attains the highest end of all bands. If you desire to stop the auto preset memory at anytime, press the CLEAR button. 49 ADVANCED OPERATION REMOTE CONTROLLER TROUBLESHOOTING OTHERS