Marantz AV8003 AV8003 User Manua - Page 97

Other Operations

Get Marantz AV8003 PDF manuals and user guides View all Marantz AV8003 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

NAMES AND FUNCTION CONNECTIONS SETUP BASIC OPERATION ENGLISH CLONE MODE Creating copies using clone mode All of the codes programmed to the RC101 remote controller can be copied to another RC101 using a few simple operations. • The remote controller can copy the entire contents. • When copying the entire contents, all programmed codes are copied. Note: The clone function can only be used for copying when using the same model (RC101) for both the transmitting and receiving remote controller. Copying entire contents 1. Place the receiver sensor of the receiving remote controller (top) so that it is facing the transmitter of the transmitting remote controller (top) at a distance of about 2 inchs (5 cm). 2 inchs (5 cm) SYSTEM REMOTE CONTROLLER 2. Press SET button and PLAY button of the transmitting remote controller until the SEND indicator blinks twice. SYSTEM REMOTE CONTROLLER 4. Press the ENTER cursor button on the receiving remote controller. Then back lights tune off. 5. Press the ENTER cursor button on the transmitting remote controller. Then backlights tune off. 6. When copying is started, the SEND indicator of transmitting remote controller and the LEARN indicator of receiving remote controller start to blink. When the copying operation is completed, the back lights of transmitting remote controller and receiving remote controller are turned on. Do not touch either of the remote controls during the copying operation. Doing so could cause copying to fail. If the copying fails in the middle of the copying process, back light of receiving remote are flash. Press the SET button to return the normal mode. Check and perform steps 1 to 5 again. Copying takes about 30 seconds to complete when the transmitting remote controller has been programmed to 100% capacity. OTHER OPERATIONS CHANGE THE ZONE CONTROL COMMANDS FOR EACH ZONE (When operating the unit by Multi Zone connected) • Zone A (Default) • Zone B • Zone C (The unit does not use this zone.) • Zone D (MAIN ZONE) Change the control commands for each zone. 2. 1. 1. Press SET button and ZONE button until the SEND indicator blinks twice. Then backlight flashes. 2. Press each zone button(A/B button) When the procedure is successful, the SEND indicator will blink twice. These buttons change a special code of each zone. POWER ON/OFF SOURCE CHANGE THE CONTROL COMMANDS OF ZONE SPEAKER FUNCTION FROM ZONE. 1. 3. 2. 1. 1. Press SET button and POWER ON button until the SEND indicator blinks twice. Then backlight flashes. 2. Press the 1-digit code by numeric keys. • Zone mode: 1 (Default) • Zone speaker mode: 2 Note In case of Zone D, only control for main zone is possible. 3. Press ENTER button once to lock in the code. When the procedure is successful, the SEND indicator will blink twice. These buttons change a special code of zone mode or zone speaker mode. Note The control commands can be set independently in ZONE A/B. POWER ON/OFF Then backlight flashes The transmitting side is now ready. 3. Press SET button and STOP button of the receiving remote controller until the LEARN indicator blinks twice. 7. Once copying is completed, press the SET button on both remote controls. VOL +/- MUTE INFO SLEEP Tuner mode operation remote code (Refer to page 90) VOL +/- MUTE ADVANCED OPERATION REMOTE CONTROLLER TROUBLESHOOTING OTHERS 94 Then backlight flashes. The receiving side is now ready.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
CONNECTIONS
SETUP
BASIC
OPERATION
ADVANCED
OPERATION
TROUBLESHOOTING
OTHERS
NAMES AND
FUNCTION
REMOTE
CONTROLLER
94
ENGLISH
CLONE MODE
Creating copies using clone mode
All of the codes programmed to the RC101 remote
controller can be copied to another RC101 using a
few simple operations.
• The remote controller can copy the entire
contents.
•
When copying the entire contents, all programmed
codes are copied.
Note:
The clone function can only be used for copying
when using the same model (RC101) for both the
transmitting and receiving remote controller.
Copying entire contents
1.
Place the receiver sensor of the receiving
remote controller (top) so that it is facing the
transmitter of the transmitting remote controller
(top) at a distance of about 2 inchs (5 cm).
2 inchs (5 cm)
2.
Press
SET
button and
PLAY
button of the
transmitting remote controller until the SEND
indicator blinks twice.
Then backlight flashes
The transmitting side is now ready.
3.
Press
SET
button and
STOP
button of the
receiving remote controller until the LEARN
indicator blinks twice.
Then backlight flashes.
The receiving side is now ready.
4.
Press the
ENTER
cursor button on the receiving
remote controller.
Then back lights tune off.
5.
Press the
ENTER
cursor button on the
transmitting remote controller.
Then backlights tune off.
6.
When copying is started, the SEND indicator of
transmitting remote controller and the LEARN
indicator of receiving remote controller start to
blink.
When the copying operation is completed, the
back lights of transmitting remote controller and
receiving remote controller are turned on.
Do not touch either of the remote controls
during the copying operation. Doing so could
cause copying to fail.
If the copying fails in the middle of the copying
process, back light of receiving remote are
flash. Press the
SET
button to return the
normal mode. Check and perform steps 1 to 5
again.
Copying takes about 30 seconds to complete
when the transmitting remote controller has
been programmed to 100% capacity.
7.
Once copying is completed, press the
SET
button on both remote controls.
OTHER OPERATIONS
CHANGE THE ZONE CONTROL COMMANDS FOR
EACH ZONE
(When operating the unit by Multi Zone connected)
• Zone A (Default)
• Zone B
• Zone C (The unit does not use this zone.)
• Zone D (MAIN ZONE)
Change the control commands for each zone.
2.
1.
1.
Press
SET
button and
ZONE
button until the
SEND indicator blinks twice.
Then backlight flashes.
2.
Press each zone button(A/B button)
When the procedure is successful, the SEND
indicator will blink twice.
These buttons change a special code of each zone.
POWER ON/OFF
SOURCE
INFO
VOL +/–
SLEEP
MUTE
Tuner mode operation remote code (Refer to page
90)
CHANGE THE CONTROL COMMANDS OF ZONE
SPEAKER FUNCTION FROM ZONE.
1.
2.
1.
3.
1.
Press
SET
button and
POWER ON
button until
the SEND indicator blinks twice.
Then backlight flashes.
2.
Press the 1-digit code by numeric keys.
• Zone mode: 1 (Default)
• Zone speaker mode:
2
Note
In case of Zone D, only control for main zone is
possible.
3.
Press
ENTER
button once to lock in the code.
When the procedure is successful, the SEND
indicator will blink twice.
These buttons change a special code of zone mode
or zone speaker mode.
Note
The control commands can be set independently in
ZONE A/B.
POWER ON/OFF
VOL +/–
MUTE