Marantz AV8003 AV8003 User Manua - Page 53

ENGLISH NAMES AND FUNCTION BASIC OPERATION MANUAL PRESET MEMORY 3. 2. 4. CONNECTIONS AV PRE TUNER AV8003 INPUT SELECTOR PURE DIRECT M-DAX SURROUND MODE AUTO PURE DIRECT PHONES ZONE THX ZONE SPEAKER 7.1CH INPUT SETUP MIC MENU EXIT ENTER UP HDMI 4. DOWN VOLUME BAND TOP T-MODE M-DAX MEMORY DISPLAY 3.CLEAR 5. 4. 3. SETUP (Using the unit) 1. Tune into the radio station you desire (Refer to the "MANUAL TUNING" or "AUTO TUNING" section). 2. Press the MEMORY button on the front panel. "- -" (preset number) starts blinking on the display. 3. Select the preset number by pressing the 1 or 2 cursor buttons, while this is still blinking (approx. 5 seconds) 4. Press the MEMORY button again to enter. The display stops blinking. The station is now stored in the specified preset memory location. (Using the remote controller) 1. Tune into the radio station you desire (Refer to the "MANUAL TUNING" or "AUTO TUNING" section). 2. Switch the remote controller to TUNER mode. 3. Press the < / > button until 002 is displayed in TUNER mode. 4. Press the MEMORY button on the remote controller. "- -" (preset number) starts blinking on the display. 5. Enter the desired preset number by pressing the numeric buttons. Note: • When entering a single digit number (2 for example), either input "02" or just input "2" and wait for a few seconds. TROUBLESHOOTING OTHERS 50 RECALLING A PRESET STATION 2. 2. (Using the unit) 1. Select the desired preset station by pressing the 1 or 2 cursor buttons on the front panel. (Using the remote controller) 1. Switch the remote controller to TUNER mode. 2. Press the 1 or 2 cursor buttons to tune in the deseired preset station. Or enter the preset station number with the numeric buttons. Note: The same operations performed using the 1 or 2 buttons can be performed using the CH +/- buttons when the remote controller is in TUNER mode. PRESET SCAN 2.5. 2.5. 2. 2. 4. 5. (Using the remote controller) 1. Switch the remote controller to TUNER mode. 2. Press the < / > button until 002 is displayed and press the P-SCAN button on the remote. "PRESET SCAN" appears on the front display and then the preset station with the lowest preset number is recalled first. 3. Preset stations are recalled in sequence (No.1 → No.2 → etc.) for 10 seconds each. No stored preset number will be skipped. 4. You can fast forward the preset stations, press the 2 cursor button continuously. 5. When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or P-SCAN button on the remote controller. PRESET CHANNEL LIST DISPLAY A complete list of the broadcast channels stored in this unit can be displayed. 2. 4. 2. 4. 2. 2. 1. Switch the remote controller to TUNER mode. 2. Press < / > on the remote controller to display 002, then press P-INFO button. 3. The list of preset channels will be displayed on the screen of the TV monitor connected to this unit. PRESET LIST NO. 1 NO. 2 NO. 3 NO.10 FM 87.10 FM 93.10 FM 94.70 FM105.70 MHz MHz MHz MHz RETURN NEXT EXIT On the unit, multicast channels are also displayed, as shown below, when an HD Radio channel is set to the preset channels. PRESET LIST NO. 1 NO. 2 NO. 3 NO. 4 NO. 5 NO.10 FM 87.10 FM 93.10 FM 94.70 FM 94.70 FM 94.70 FM105.70 MHz MHz MHz MHz-3 MHz-4 MHz In the list of preset channels above, preset numbers 4 and 5 are the multicast channels for preset number 3. 4. Up to 10 channels can be displayed at a time. If there are more than 10 channels, press P-INFO button on the remote controller once more to display the next page. The list display will disappear automatically in 5 seconds. CLEARING STORED PRESET STATIONS You can remove preset stations from the memory using the following procedure. 2. 3. STANDBY POWER ON/OFF INPUT SELECTOR PURE DIRECT M-DAX AV PRE TUNER AV8003 UP HDMI DOWN VOLUME SURROUND MODE AUTO PURE DIRECT PHONES ZONE THX ZONE SPEAKER 7.1CH INPUT SETUP MIC MENU EXIT ENTER BAND T-MODE MEMORY CLEAR TOP M-DAX DISPLAY 2. 2. 3. 1. Recall the preset number to be cleared with the method described in "Recalling" a preset station. 2. Press the MEMORY button on the front panel or press the MEMORY button on the remote. 3. The stored preset number blinks in the display for 5 seconds. While blinking, press the CLEAR button on the front panel or the remote controller. 4. "xx CLEAR" appears on the display to indicate that the specified preset number has been cleared. Note: • To clear all stored preset stations, press and hold the CLEAR and the ENTER buttons for two seconds. ADVANCED OPERATION REMOTE CONTROLLER