Motorola WR850G User Guide - Page 71

Port Forwards, LAN IP Address, LAN Port Range, Port Triggers, Enabled, Operation Mode, Router

Page 71 highlights

Section 3 Configuration Port Forwards: (continued) To forward communications from a single port, enter the same port number in both fields. This information must be entered for each port forward. FACTORY DEFAULT: (blank) (2) LAN IP Address: Sets the client on your local network (specified by IP address) to which communications will be forwarded. This information must be entered for each port forward. FACTORY DEFAULT: (blank) (3) LAN Port Range: Port Triggers: (ADVANCED) These two fields ("Start" and "End") define a range of LAN ports to which communications will be forwarded. To forward to a single port, enter the same port number in both fields. This information is optional for each port forward. FACTORY DEFAULT: (blank) Sets rules for forwarding inbound communications (from your broadband connection) based on specific outbound communications (or "triggers") from a LAN client. Specifically, if a LAN client transmits to the Internet using any of a set of outbound destination ports, they will be forwarded Internet responses that are received on a corresponding set of inbound destination ports. You may optionally specify a destination port range for forwards, on the LAN side of the WR850, as well. This feature can be particularly useful to support real-time games which require Internet responses to game activity. These responses might otherwise be blocked by the WR850 firewall. NOTE: These settings are only used if Operation Mode on the BASIC Page is set to Router. You can store up to 20 port triggers, and selectively enable one or more of them when desired, using the Enabled checkbox at the end of each row. If more port triggers are required, especially for a single client, you should consider configuring the client as a DMZ. NOTE: Port triggers will be applied in the order in which they are listed on this page. (continued on next page) 3-38 WR850

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123

Section 3
Configuration
3-38
WR850
Port Forwards:
(continued)
To forward communications from a single port, enter the same port
number in both fields.
This information must be entered for each port forward.
FACTORY DEFAULT:
(blank)
(2) LAN IP Address
:
Sets the client on your local network (specified by IP address) to
which communications will be forwarded.
This information must be entered for each port forward.
FACTORY DEFAULT:
(blank)
(3) LAN Port Range
:
These two fields (“Start” and “End”) define a range of LAN ports to
which communications will be forwarded.
To forward to a single
port, enter the same port number in both fields.
This information is optional for each port forward.
FACTORY DEFAULT:
(blank)
Port Triggers:
(ADVANCED)
Sets rules for forwarding inbound communications (from your
broadband connection) based on specific outbound communications
(or “triggers”) from a LAN client.
Specifically, if a LAN client transmits to the Internet using any of a
set of outbound destination ports, they will be forwarded Internet
responses that are received on a corresponding set of inbound
destination ports.
You may optionally specify a destination port range for forwards, on
the LAN side of the WR850, as well.
This feature can be particularly useful to support real-time games
which require Internet responses to game activity.
These responses
might otherwise be blocked by the WR850 firewall.
NOTE
:
These settings are only used if
Operation Mode
on the BASIC
Page is set to
Router
.
You can store up to 20 port triggers, and selectively enable one or
more of them when desired, using the
Enabled
checkbox at the end
of each row.
If more port triggers are required, especially for a
single client, you should consider configuring the client as a DMZ.
NOTE
:
Port triggers will be applied in the order in which they are listed
on this page.
(continued on next page)