NEC NP-PE401H User's Manual - Page 17

Attaching the Cable Cover, Procedure for Attaching the Cable Cover

Get NEC NP-PE401H PDF manuals and user guides View all NEC NP-PE401H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Introduction 8 POWER ON/ Power on the projector. Refer to OFF and LED the "Power On/Off the Projec- indicator tor" section on pages 27-28. 9 ECO Dim the projector lamp which will lower power consumption and extend the lamp life. (refer to page 52) 10 SOURCE Press "SOURCE" to select an input signal. 11 AUTO ADJ. Automatically synchronize the projector to the input source. 12 STATUS LED Indicate the projector's tempera- ture status. 13 LAMP LED Indicate the projector's lamp status. CAUTION: • Be sure to tighten the screws after attaching the cable cover. Failure to do so may cause the cable cover to come off and fall, resulting in injury or damage to the cable cover. • Do not put bundled cables in the cable cover. Failure to do so may damage the power cord, resulting a fire. Attaching the Cable Cover Cable Cover 1 2 Procedure for Attaching the Cable Cover: 1. Mount the cable cover to the projector.  2. Tighten two screws on both sides of the cable cover.  English ... 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
10
English ...
Introduction
8
POWER ON/
OFF and LED
indicator
Power on the projector. Refer to
the “Power On/Off the Projec-
tor” section on pages 27-28.
9
ECO
Dim the projector lamp which
will lower power consumption
and extend the lamp life. (refer
to page 52)
10
SOURCE
Press “SOURCE” to select an
input signal.
11
AUTO ADJ.
Automatically synchronize the
projector to the input source.
12
STATUS LED
Indicate the projector’s tempera-
ture status.
13
LAMP LED
Indicate the projector’s lamp
status.
Attaching the Cable Cover
Procedure for Attaching the Cable Cover:
1. Mount the cable cover to the projector.
2. Tighten two screws on both sides of the cable cover.
Cable Cover
1
2
CAUTION:
• Be sure to tighten
the screws after
attaching the cable
cover. Failure to do
so may cause the
cable cover to come
off and fall, result-
ing in injury or
damage to the cable
cover.
• Do not put bundled
cables in the cable
cover. Failure to do
so may damage the
power cord, result-
ing a fire.