NEC NP-PE401H User's Manual - Page 22

Using the Downloadable Software, Using the Computer Cable VGA to Operate

Get NEC NP-PE401H PDF manuals and user guides View all NEC NP-PE401H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

Introduction Using the Downloadable Software Using the Computer Cable (VGA) to Operate the  When "Computer IN" is selected for Projector (Virtual Remote Tool) input, the Virtual Using the utility software "Virtual Remote Tool" that you can Remote screen or the download from our web site (http://www.nec-display.com/ toolbar will be dis- dl/en/index.html), Virtual Remote screen (or toolbar) can be played as well as your displayed on your computer screen. computer screen. This will help you perform operations such as projector's  Use the supplied power on or off and signal selection via the computer cable computer cable (VGA) (VGA), serial cable, or LAN connection. to connect the COM- PUTER IN connector directly with the moni- tor output connector of the computer to use Virtual Remote Tool. Using a switcher or other cables than the supplied computer cable (VGA) may Virtual Remote screen Toolbar cause failure in signal communication. VGA cable connector: This section provides an outline of preparation for use of Virtual Remote Tool. Pin Nos. 12 and 15 are For information on how to use Virtual Remote Tool, see Help of Vir- required for DDC/CI. tual Remote Tool. (-> page 19)  Virtual Remote Tool may not work depending on your computer's specifications and version of • Step 1: Install Virtual Remote Tool on the computer. (-> page 16) • Step 2: Connect the projector to the computer. (-> page 17) • Step 3: Start Virtual Remote Tool. (-> page 18) graphic adapters or drivers. TIP:  The projector does not support the LAN automatic search feature of Virtual Remote • V irtual Remote Tool can be used with a LAN and a serial connection. • F or update information on Virtual Remote Tool, visit our website: http://www.nec-display.com/dl/en/index.html Tool. To connect the projector, register an TIP: IP address manually. • The projector's COMPUTER IN connector supports DDC/CI (Display Data Channel Command Interface). DDC/CI is a standard interface for bidirec- tional communication between display/projector and computer. 15 ... English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
15
... English
Introduction
Using the Downloadable Software
Using the Computer Cable (VGA) to Operate the
Projector (Virtual Remote Tool)
Using the utility software “Virtual Remote Tool” that you can
download from our web site (http://www.nec-display.com/
dl/en/index.html), Virtual Remote screen (or toolbar) can be
displayed on your computer screen.
This will help you perform operations such as projector’s
power on or off and signal selection via the computer cable
(VGA), serial cable, or LAN connection.
Virtual Remote screen
Toolbar
This section provides an outline of preparation for use of Virtual
Remote Tool.
For information on how to use Virtual Remote Tool, see Help of Vir-
tual Remote Tool. (-> page 19)
• Step 1: Install Virtual Remote Tool on the computer. (-> page 16)
• Step 2: Connect the projector to the computer. (-> page 17)
• Step 3: Start Virtual Remote Tool. (-> page 18)
TIP:
• Virtual Remote Tool can be used with a LAN and a serial connection.
• For update information on Virtual Remote Tool, visit our website:
TIP:
• The projector’s COMPUTER IN connector supports DDC/CI (Display Data
Channel Command Interface). DDC/CI is a standard interface for bidirec-
tional communication between display/projector and computer.
When “Computer
IN” is selected for
input, the Virtual
Remote screen or the
toolbar will be dis-
played as well as your
computer screen.
Use the supplied
computer cable (VGA)
to connect the COM-
PUTER IN connector
directly with the moni-
tor output connector
of the computer to use
Virtual Remote Tool.
Using a switcher or
other cables than the
supplied computer
cable (VGA) may
cause failure in signal
communication.
VGA cable connector:
Pin Nos. 12 and 15 are
required for DDC/CI.
Virtual Remote
Tool may not work
depending on your
computer’s specifica
-
tions and version of
graphic adapters or
drivers.
The projector does
not support the LAN
automatic search fea-
ture of Virtual Remote
Tool. To connect the
projector, register an
IP address manually.