Home » Netgear Manuals » Network Security & Firewall Devices » Netgear DGFV338 » Manual Viewer

Netgear DGFV338 DGFV338 Reference Manual - Page 45

DNS lookup using WAN DNS Servers ISP DNS Servers., Use Dedicated WAN port.

Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

DGFV338 ProSafe Wireless ADSL Modem VPN Firewall Router Reference Manual • Use Dedicated WAN port. - Dedicated ADSL. If you have configured only the ADSL ISP, then select this interface. In this mode the ADSL interface will always be active and all traffic will be sent over this link; the other link will always be down. No link failure detection will occur. - Dedicated Ethernet. If this is your only ISP configuration, then select Dedicated Ethernet. In this mode the Ethernet interface will always be active and all traffic will be sent over this link; the other link will always be down. No link failure detection will occur. WAN failure is detected using DNS queries to a DNS server, or a Ping to an IP address. For each WAN interface, DNS queries or Ping requests are sent to the specified IP address. If replies are not received, the corresponding WAN interface is considered down. • DNS lookup using WAN DNS Servers (ISP DNS Servers). In this case, DNS queries are sent to the DNS server configured on the ADSL and Ethernet ISP pages (see "Configuring Your Internet Connection using Auto Detect" on page 2-4). • DNS lookup using this DNS Server (for example, a public DNS Server), As an option, you can enter any public DNS server address. DNS queries are sent to this server through the WAN interface being monitored. • Ping to this IP address. Enter a public IP address that will not reject the Ping request or will not consider the traffic abuse. Queries are sent to this server through the WAN interface being monitored. • Test Period. DNS query is sent periodically after every test period. The default test period is 30 seconds. • Failover. The WAN interface is considered down after the configured number of queries have failed to elicit a reply from the configured DNS server or from the Ping destination. The minimum number of failed queries is two. The rollover link is brought up after this, if AutoRollover has been selected. To configure the WAN mode: 1. Select Network Configuration from the main menu and WAN Mode from the submenu. The WAN Mode screen will display. 2. Select either the NAT or Classical Routing radio button. If you have a single Internet address, you must use NAT. Basic Installation and Configuration v1.0, April 2007 2-15

Section	Page
DGFV338 ProSafe Wireless ADSL Modem VPN Firewall Router Reference Manual	1
Contents	11
About This Manual	17
Conventions, Format and Scope	17
How to Use This Manual	18
How to Print this Manual	18
Chapter 1 Introduction	21
Key Features of the NETGEAR ProSafe DGFV338	21
Full Routing on Both the ADSL and 10/100 WAN Port	22
A Powerful, True Firewall with Content Filtering	22
Security	23
Virtual Private Networking (VPN)	23
Autosensing Ethernet Connections with Auto Uplink	23
Extensive Protocol Support	24
Easy Installation and Management	24
Maintenance and Support	25
System Requirements	25
Package Contents	26
Hardware Description	26
Router Front Panel	26
Router Rear Panel	28
Router Login Factory Defaults	29
Placement of your NETGEAR ProSafe DGFV338	30
Chapter 2 Basic Installation and Configuration	31
Using ADSL Microfilters (optional)	32
Logging in and Configuring your Internet Connection	33
Configuring Your Internet Connection using Auto Detect	34
Manually Configuring your ADSL Connection	36
Manually Configuring your Ethernet Connection	38
Selecting Advanced Options for your Ethernet or ADSL Connection	40
Configuring the WAN Mode	44
Configuring Dynamic DNS (If Needed)	47
Programming the Traffic Meter	50
Chapter 3 Wireless Configuration	53
Implementing Wireless Security	53
Understanding Wireless Settings	55
Wireless LANs	56
Access Control List	58
Wireless Advanced Options	59
Advanced Wireless Router Settings	59
WEP and WPA/WPA2 Wireless Security Check List Form	60
Configuring Your Wireless Settings	61
Configuring WEP	62
Configuring WPA-PSK	64
Configuring WPA2-PSK	65
Configuring WPA-PSK and WPA2-PSK	66
Configuring WPA with RADIUS	67
Configuring WPA2 with RADIUS	68
Configuring WPA and WPA2 with RADIUS	69
Restricting Wireless Access by MAC Address	70
Chapter 4 Security and Firewall Protection	73
Firewall Protection and Content Filtering Overview	73
Using Rules to Block or Allow Specific Kinds of Traffic	73
About Service Based Rules	74
Outbound Rules (Service Blocking)	75
The DGFV338 allows you to block the use of certain Internet services by PCs on your network. This is called service blocking or port filtering.	75
Outbound Rule Example: Blocking Instant Messenger	79
Inbound Rules (Port Forwarding)	79
Because the DGFV338 uses Network Address Translation (NAT), your network presents only one IP address to the Internet and outsid...	79
Inbound Rule Example: A Local Public Web Server	84
Inbound Rule Example: Allowing Videoconference from Restricted Addresses	84
Inbound Rule Example: One-to-One NAT Mapping	85
Inbound Rule Example: Exposed Host	87
Considerations for Inbound Rules	88
Order of Precedence for Rules	89
Customized Services	89
Quality of Service (QoS) Priorities	91
Attack Checks	92
Managing Groups and Hosts	93
Blocking Internet Sites	96
Enabling Source MAC Filtering	99
Setting up Port Triggering	100
Setting a Schedule to Block or Allow Specific Traffic	103
Event Logs and Alerts	104
Security and Administrator Management	107
Chapter 5 Virtual Private Networking	109
Dual WAN Port Systems	109
Setting up a VPN Connection using the VPN Wizard	110
VPN Tunnel Policies	113
IKE Policy	113
Managing IKE Policies	114
IKE Policy Table	114
VPN Policy	115
Managing VPN Policies	115
VPN Policy Table	116
VPN Tunnel Connection Status	116
Creating a VPN Connection: Between FVX538 and DGFV338	117
Configuring the ProSafe DGFV338	117
Configuring the FVX538	122
Testing the Connection	123
Creating a VPN Client Connection: VPN Client to DGFV338	123
Configuring the DGFV338	123
Configuring the VPN Client	125
Testing the Connection	129
Certificate Authorities	130
Generating a Self Certificate Request	131
Uploading a Trusted Certificate	133
Managing your Certificate Revocation List (CRL)	133
Extended Authentication (XAUTH) Configuration	134
Configuring XAUTH for VPN Clients	135
User Database Configuration	137
RADIUS Client Configuration	138
Manually Assigning IP Addresses to Remote Users (ModeConfig)	140
Mode Config Operation	140
Configuring the ProSafe DGFV338	141
Configuring the ProSafe VPN Client for ModeConfig	144
Chapter 6 Router and Network Management	149
Performance Management	149
Wireless Firewall Features That Reduce Traffic	149
Service Blocking	150
Block Sites	151
Source MAC Filtering	152
Wireless Firewall Features That Increase Traffic	152
Port Forwarding	152
Port Triggering	154
VPN Tunnels	154
Using QoS to Shift the Traffic Mix	154
Tools for Traffic Management	155
Administrator and Guest Access Authorization	155
Changing the Passwords and Login Time-out	155
Enabling Remote Management Access	156
Command Line Interface	158
Event Alerts	159
Traffic Limits Reached	159
Monitoring	160
Router Status	160
WAN Ports	162
Internet Traffic	163
LAN Ports and Attached Devices	165
Known PCs and Devices	165
DHCP Log	166
Port Triggering Status	167
Firewall Security	167
VPN Tunnels	169
Using a SNMP Manager	170
Diagnostics	172
Configuration File Management	174
Settings Backup and Firmware Upgrade	174
Backup and Restore Settings	174
Router Upgrade	176
Setting the Time Zone	177
Chapter 7 LAN Configuration	179
Using the Firewall as a DHCP server	179
Configuring the LAN Setup Options	180
Using Address Reservation	181
Configuring Multi Home LAN IPs	182
Configuring Static Routes	185
Adding or Editing a Static Route	185
Routing Information Protocol (RIP)	186
Static Route Example	188
Enabling Universal Plug and Play (UPnP)	188
Chapter 8 Troubleshooting	191
Basic Functions	191
Power LED Not On	191
LEDs Never Turn Off	192
LAN or Internet Port LEDs Not On	192
Troubleshooting the Web Configuration Interface	192
Troubleshooting the ISP Connection	193
Troubleshooting a TCP/IP Network Using a Ping Utility	195
Testing the LAN Path to Your Firewall	195
Testing the Path from Your PC to a Remote Device	196
Restoring the Default Configuration and Password	197
Problems with Date and Time	197
Appendix A Default Settings and Technical Specifications	199
Default Factory Settings	199
Technical Specifications	201
Appendix B Related Documents	203

Match case Limit results 1 per page

DGFV338 ProSafe Wireless ADSL Modem VPN Firewall Router Reference Manual

Basic Installation and Configuration

2-15

v1.0, April 2007

•

Use Dedicated WAN port.

–

Dedicated ADSL

. If you have configured only the ADSL ISP, then select this interface. In

this mode the ADSL interface will always be active and all traffic will be sent over this

link; the other link will always be down. No link failure detection will occur.

–

Dedicated Ethernet.

If this is your only ISP configuration, then select Dedicated

Ethernet. In this mode the Ethernet interface will always be active and all traffic will be

sent over this link; the other link will always be down. No link failure detection will occur.

WAN failure is detected using DNS queries to a DNS server, or a Ping to an IP address. For each

WAN interface, DNS queries or Ping requests are sent to the specified IP address. If replies are not

received, the corresponding WAN interface is considered down.

•

DNS lookup using WAN DNS Servers (ISP DNS Servers).

In this case, DNS queries are

sent to the DNS server configured on the ADSL and Ethernet ISP pages (see

“Configuring

Your Internet Connection using Auto Detect” on page 2-4

•

DNS lookup using this DNS Server (for example, a public DNS Server)

, As an option, you

can enter any public DNS server address. DNS queries are sent to this server through the WAN

interface being monitored.

•

Ping to this IP address

. Enter a public IP address that will not reject the Ping request or will

not consider the traffic abuse. Queries are sent to this server through the WAN interface being

monitored.

•

Test Period

. DNS query is sent periodically after every test period. The default test period is

30 seconds.

•

Failover

. The WAN interface is considered down after the configured number of queries have

failed to elicit a reply from the configured DNS server or from the Ping destination. The

minimum number of failed queries is two. The rollover link is brought up after this, if Auto-

Rollover has been selected.

To configure the WAN mode:

Select

Network Configuration

from the main menu and

WAN Mode

from the submenu. The

WAN Mode screen will display.

Select either the

NAT

Classical Routing

radio button. If you have a single Internet address,

you must use NAT.