Netgear GS752TS GS7xxTS-TPS Hardware Installation Guide - Page 13

GS728TPS Front-Panel and Back-Panel Configuration

Get Netgear GS752TS PDF manuals and user guides View all Netgear GS752TS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

GS728TS, GS728TPS, GS752TS, and GS752TPS Smart Switch Hardware Installation Guide The front panel contains the following: • 24 RJ-45 connectors for 10/100/1000 Mbps autosensing Gigabit Ethernet switching ports. • 2 combo ports (port 23 and 24) to support 10/100/1000 Mbps copper or 100M/1G optical module. • 2 dedicated SFP ports (port 25 and 26) to support 1G optical module. • 2 dedicated SFP ports (port 27 and 28) to support 1G optical module (uplink) or 2.5G stacking (via stacking cable). • Up to two of these ports (ports 27 and 28) can alternatively be used as stacking ports • Reset button to restart the device. • Recessed default reset button to restore the device back to the factory defaults. • Link, Speed, and Activity LEDs for each port. • Power, Fan Status, Stack Master, and Stack ID LEDs. Figure 3 illustrates the NETGEAR GS728TS Smart Switch back panel. Figure 3. GS728TS Back Panel The back panel contains a power connector. Power Connector GS728TPS Front-Panel and Back-Panel Configuration The GS728TPS Smart Switch has 24 10/100/1000 Mbps PoE capable copper ports and 6 SFP fiber ports, 2 of which are combo ports. Up to two SFP ports (port 27 and 28) at a time can be used as stacking ports. Each port is capable of sensing the line speed and negotiating the duplex mode with the link partner automatically. Figure 4 illustrates the front panel of the NETGEAR GS728TPS Smart Switch. Chapter 2. Physical Description | 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
Chapter 2.
Physical Description
|
13
GS728TS, GS728TPS, GS752TS, and GS752TPS Smart Switch Hardware Installation Guide
The front panel contains the following:
•
24 RJ-45 connectors for 10/100/1000 Mbps autosensing Gigabit Ethernet switching ports.
•
2 combo ports (port 23 and 24) to support 10/100/1000 Mbps copper or 100M/1G optical
module.
•
2 dedicated SFP ports (port 25 and 26) to support 1G optical module.
•
2 dedicated SFP ports (port 27 and 28) to support 1G optical module (uplink) or 2.5G
stacking (via stacking cable).
•
Up to two of these ports (ports 27 and 28) can alternatively be used as stacking ports
•
Reset button to restart the device.
•
Recessed default reset button to restore the device back to the factory defaults.
•
Link, Speed, and Activity LEDs for each port.
•
Power, Fan Status, Stack Master, and Stack ID LEDs.
Figure
3
illustrates the NETGEAR GS728TS Smart Switch back panel.
Power Connector
Figure 3. GS728TS Back Panel
The back panel contains a power connector.
GS728TPS Front-Panel and Back-Panel Configuration
The GS728TPS Smart Switch has 24 10/100/1000 Mbps PoE capable copper ports and 6
SFP fiber ports, 2 of which are combo ports. Up to two SFP ports (port 27 and 28) at a time
can be used as stacking ports.
Each port is capable of sensing the line speed and negotiating the duplex mode with the link
partner automatically.
Figure
4
illustrates the front panel of the NETGEAR GS728TPS Smart Switch.