Netgear GS752TS GS7xxTS-TPS Hardware Installation Guide - Page 17

LED Designations, RJ-45 Port LEDs

Get Netgear GS752TS PDF manuals and user guides View all Netgear GS752TS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

GS728TS, GS728TPS, GS752TS, and GS752TPS Smart Switch Hardware Installation Guide Figure 9. GS752TPS Back Panel The back panel contains a power connector. LED Designations Power Connector RJ-45 Port LEDs The following table describes the RJ-45 port LED designations. There is one LED for each RJ-45 port. LED Designation Ethernet Mode: SPD/Link/ACT LED • Off- No link established. • Solid Green - A valid 1000 Mbps link is established. • Blinking Green - The port is transmitting or receiving packets at 1000 Mbps. • Solid Yellow - A valid 10/100 Mbps link is established. • Blinking Yellow - The port is transmitting or receiving packets at 10/100 Mbps. PoE Mode: PoE Status LED • Off - No PoE powered device (PD) is connected. • Solid Green -The PoE powered device (PD) is connected and the port is supplying power successfully. • Solid Yellow - Indicates one of the following failures resulted in stopping power to that port: - Short circuit on the PoE power circuit. - PoE power demand exceeds the power available. - PoE current exceeds the PD's classification. - Out of proper voltage band (44 ~ 57 VDC for af, 50~57 VDC for at). Note: If the port media is changed to fiber, the Ethernet LED will change to the OFF status. Chapter 2. Physical Description | 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
Power Connector
Chapter 2.
Physical Description
|
17
GS728TS, GS728TPS, GS752TS, and GS752TPS Smart Switch Hardware Installation Guide
Figure 9. GS752TPS Back Panel
The back panel contains a power connector.
LED Designations
RJ-45 Port LEDs
The following table describes the RJ-45 port LED designations. There is one LED for each
RJ-45 port.
LED
Designation
Ethernet Mode: SPD/Link/ACT
LED
•
Off
—
No link established.
•
Solid Green
—
A valid 1000 Mbps link is established.
•
Blinking Green
—
The port is transmitting or receiving packets at
1000
Mbps.
•
Solid Yellow
—
A valid 10/100
Mbps link is established.
•
Blinking Yellow
—
The port is transmitting or receiving packets
at
10/100
Mbps.
PoE Mode: PoE Status LED
•
Off
—
No PoE powered device (PD) is connected.
•
Solid Green
—The PoE powered device (PD) is connected and the port
is supplying power successfully.
•
Solid Yellow
—
Indicates one of the following failures resulted in
stopping power to that port:
- Short circuit on the PoE power circuit.
- PoE power demand exceeds the power available.
- PoE current exceeds the PD's classification.
- Out of proper voltage band (44 ~ 57 VDC for af, 50~57 VDC for at).
Note:
If the port media is changed to fiber, the Ethernet LED will change to
the OFF status.