Nokia IP2255 Installation Guide - Page 75

To remove, install, or replace the Nokia encryption accelerator

Get Nokia IP2255 - Security Appliance PDF manuals and user guides View all Nokia IP2255 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Removing, Installing, and Replacing the Nokia Encryption Accelerator Card To remove, install, or replace the Nokia encryption accelerator card 1. Use Network Voyager or the CLI halt command to perform an orderly shutdown of the appliance. Note You do not need to turn off power to the security platform. For information about how to access Network Voyager and the related reference materials, see "Using Nokia Network Voyager" on page 53. 2. Identify the location of the NIC or cover plate to remove. 3. Loosen the two retaining screws on the front plate of the NIC. Caution To avoid damage to the ejector and locking lever, loosen the two retaining screws before you remove any NIC. One screw is located behind the ejector and locking lever, and the other screw is on the opposite side of the NIC. Note If no NIC is currently installed, remove the two retaining screws on the blank plate that covers the slot and proceed to step 8. 4. Press the red button on the ejector and locking lever on the encryption accelerator card. The lock is released. Nokia IP2255 Security Platform Installation Guide 75

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Removing, Installing, and Replacing the Nokia Encryption Accelerator Card
Nokia IP2255 Security Platform Installation Guide
75
To remove, install, or replace the Nokia encryption accelerator
card
1.
Use Network Voyager or the CLI halt command to perform an orderly
shutdown of the appliance.
Note
You do not need to turn off power to the security platform.
For information about how to access Network Voyager and the related
reference materials, see
“Using Nokia Network Voyager”
on page 53.
2.
Identify the location of the NIC or cover plate to remove.
3.
Loosen the two retaining screws on the front plate of the NIC.
Caution
To avoid damage to the ejector and locking lever, loosen the two
retaining screws before you remove any NIC. One screw is located
behind the ejector and locking lever, and the other screw is on the
opposite side of the NIC.
Note
If no NIC is currently installed, remove the two retaining screws on the
blank plate that covers the slot and proceed to
step 8
.
4.
Press the red button on the ejector and locking lever on the encryption
accelerator card.
The lock is released.