Pioneer PRO110FD Owner's Manual - Page 112

Message, Check, Problem, Possible Solution - error code

Get Pioneer PRO110FD - 50inch Plasma TV PDF manuals and user guides
UPC - 012562864976
View all Pioneer PRO110FD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

15 Appendix Problem OTHER • TV-Guide data cannot be obtained. • An external device connected to the USB port does not operate. • Photo data stored in a digital still camera cannot be read through USB interface. • Panel sounds/noises. • Screen displays uneven brightness on the sides. Possible Solution • If TV-Guide data cannot be obtained with ANT.A selected for cable connection, select ANT.B for over the air. In addition, try the TV-Guide setup again by performing the following procedure (see page 39): - Select "Antenna" for "Select service(s)" on Screen 3. - Select "ANT B IN" on Screen 4. • Check if the device is connectable to the display. (See page 79.) • Re-insert the USB cable. (See page 79.) • For connection, use a USB cable shorter than 5 m. (See page 79.) • Check if the USB cable is properly connected. (See page 79.) • First turn the power off and then turn it on again in order to check if the external device works correctly. • Check if the external device works correctly after the USB device was restarted. • Check if the digital still camera is in the viewing mode. • Refer to the instruction manual for the digital still camera. • Check if the device is connectable to the display. (See page 79.) • Check if the digital still camera is turned on. • Panel generated sounds, examples: Fan motor noise, Electrical Circuit Humming / Glass Panel buzzing are normal operation of a phosphor-based matrix display. • Display content that completely fills the screen until unevenness is minimized. Some signals may require to change the AV mode setting. (See page 68.) If the following error codes appear on the screen, check the corresponding items in the table. Code SD04 and SD11 Message Powering off. Internal temperature too high. Check temperature around PDP. Check Check if the ambient temperature of the plasma display is high. SD05 Internal protection circuit turns power off. Is there a short in speaker cable? Check the speaker cable connections between the plasma display and the speakers. 112 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
112
En
Appendix
15
If the following error codes appear on the screen, check the corresponding items in the table.
OTHER
• TV-Guide data cannot be obtained.
•If TV-Guide data cannot be obtained with ANT.A selected for cable connection, select ANT.B for over the air.
In addition, try the TV-Guide setup again by performing the following procedure (see page 39):
-
Select “Antenna” for “Select service(s)” on Screen 3.
-
Select “ANT B IN” on Screen 4.
• An external device connected to the
USB port does not operate.
• Check if the device is connectable to the display. (See page 79.)
• Re-insert the USB cable. (See page 79.)
• For connection, use a USB cable shorter than 5 m. (See page 79.)
• Check if the USB cable is properly connected. (See page 79.)
• First turn the power off and then turn it on again in order to check if the external device works correctly.
• Check if the external device works correctly after the USB device was restarted.
• Check if the digital still camera is in the viewing mode.
• Refer to the instruction manual for the digital still camera.
• Photo data stored in a digital still
camera cannot be read through USB
interface.
• Check if the device is connectable to the display. (See page 79.)
• Check if the digital still camera is turned on.
• Panel sounds/noises.
• Panel generated sounds, examples: Fan motor noise, Electrical Circuit Humming / Glass Panel buzzing are
normal operation of a phosphor-based matrix display.
• Screen displays uneven brightness on
the sides.
• Display content that completely fills the screen until unevenness is minimized.
Some signals may require to
change the AV mode setting. (See page 68.)
Code
Message
Check
SD04 and
SD11
Powering off. Internal temperature too high.
Check temperature around PDP.
Check if the ambient temperature of the plasma display is high.
SD05
Internal protection circuit turns power off.
Is there a short in speaker cable?
Check the speaker cable connections between the plasma display and the speakers.
Problem
Possible Solution