Ricoh 3245 Operating Instructions - Page 34

Interrupt Copy, Left Original Beeper

Page 34 highlights

Copying -How to operate ❖ To stop the machine during a multicopy run Press the {Clear/Stop} key. 2 ❖ To return the machine to the initial condition after copying Press the {Clear Modes} key. ❖ When clearing entered values Press the {Clear/Stop} key or [Clear] on the display. ❖ To check the settings Press the {Check Modes} key. Interrupt Copy Use this function to interrupt a long copy job to make urgently needed copies. Limitation ❒ You cannot use Interrupt Copy when fax originals are being scanned. A Press the {Interrupt} key. The Interrupt indicator lights. When scanning is interrupted A Remove the originals that were being copied, and then place the originals you want to copy. B Press the {Start} key. Copying starts. C When copying is complete, remove the originals and copies. D Press the {Interrupt} key again. The Interrupt indicator turns off. 20 E When the display prompts you to do so, place the former set of originals again. F Press the {Start} key. Note ❒ The previous copy job's set- tings are restored and the machine continues copying from where it left off. When the machine continues copying A Place the originals you want to copy. B Press the {Start} key. The machine stops the previous job and starts copying the new originals. C When copying is complete, remove originals and copies. D Press the {Interrupt} key again. The Interrupt indicator goes out. The previous copy job's settings are restored and the machine continues copying from where it left off. Left Original Beeper The beeper sounds and an error message is displayed if you leave originals on the exposure glass after copying. Note ❒ See p.112 "Tone: Original re- mains".

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160

Copying
20
2
-
How to operate
To stop the machine during a multi-
copy run
Press the
{
Clear/Stop
}
key.
To return the machine to the initial
condition after copying
Press the
{
Clear Modes
}
key.
When clearing entered values
Press the
{
Clear/Stop
}
key or
[
Clear
]
on the display.
To check the settings
Press the
{
Check Modes
}
key.
Interrupt Copy
Use this function to interrupt a long
copy job to make urgently needed
copies.
Limitation
You cannot use Interrupt Copy
when fax originals are being
scanned.
A
Press the
{
Interrupt
}
key.
The
Interrupt
indicator lights.
When scanning is interrupted
A
Remove the originals that were
being copied, and then place
the originals you want to copy.
B
Press the
{
Start
}
key.
Copying starts.
C
When copying is complete, re-
move the originals and copies.
D
Press the
{
Interrupt
}
key again.
The
Interrupt
indicator turns
off.
E
When the display prompts you
to do so, place the former set of
originals again.
F
Press the
{
Start
}
key.
Note
The previous copy job's set-
tings are restored and the
machine continues copying
from where it left off.
When the machine continues
copying
A
Place the originals you want to
copy.
B
Press the
{
Start
}
key.
The machine stops the previous
job and starts copying the new
originals.
C
When copying is complete, re-
move originals and copies.
D
Press the
{
Interrupt
}
key again.
The
Interrupt
indicator goes
out.
The previous copy job's settings
are restored and the machine
continues copying from where
it left off.
Left Original Beeper
The beeper sounds and an error mes-
sage is displayed if you leave origi-
nals on the exposure glass after
copying.
Note
See
p.112
Tone:
Original
re-
mains
.