Schwinn 230 Recumbent Bike 2020 model Service Manual - Page 21

Machine is on. Current is active. There is risk of electrical, shock., Disconnect all power

Get Schwinn 230 Recumbent Bike 2020 model PDF manuals and user guides View all Schwinn 230 Recumbent Bike 2020 model manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

6. Using a #2 Phillips Screwdriver, remove the 2 screws that secure the Right Main Shroud. Slowly remove the Right Main Shroud. Set the hardware and Shroud safely aside for reassembly. 7. Insert 2.5" x 10" cardboard between the Brake Magnet (C) and the Flywheel (B), and tape the cardboard to the Brake Magnet. Note: B e sure the cardboard covers all of the Brake Magnet. C B Left side 8. Turn the power on again. Machine is on. Current is active. There is risk of electrical shock. 9. Use the console to set the resistance to the highest level. This moves the Brake Magnet Arm (C1) forward. After the Brake Magnet Arm stops at the highest resistance level, turn power off. Disconnect all power and allow to sit for 5 minutes. Right side C C1 B 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
21
Left side
Right side
B
C
C
B
C1
7.
Insert 2.5” x 10” cardboard between the Brake Magnet (C) and the
Flywheel (B), and tape the cardboard to the Brake Magnet.
Note:
Be sure the cardboard covers all of the Brake Magnet.
8.
Turn the power on again.
Machine is on. Current is active. There is risk of electrical
shock.
9.
Use the console to set the resistance to the highest level. This moves
the Brake Magnet Arm (C1) forward. After the Brake Magnet Arm stops at
the highest resistance level, turn power off.
Disconnect all power and allow to sit for 5 minutes.
6.
Using a #2 Phillips Screwdriver, remove the 2 screws that secure
the Right Main Shroud. Slowly remove the Right Main Shroud. Set the
hardware and Shroud safely aside for reassembly.