Schwinn 230 Recumbent Bike 2020 model Service Manual - Page 58

Put the Drive Belt B onto the Drive Pulley A. Make sure the Drive

Get Schwinn 230 Recumbent Bike 2020 model PDF manuals and user guides View all Schwinn 230 Recumbent Bike 2020 model manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

11. Carefully pull the Pulley Shaft Assembly (H) until it works out of the Frame and releases the Washer (J), Bumper (K), Bearings (L) and Bearing Brackets (M). L M H JK M L 12. Installation is the reverse procedure. NOTICE: Do not overtighten the crank hardware as this can damage the bearings. Use these torque specs: Bracket (G)-approx. 8Nm (6lb-ft) Locknut (E)-approx. 25Nm (18.5 lb-ft) 13. Put the Drive Belt (B) onto the Drive Pulley (A). Make sure the Drive Belt is aligned on the Flywheel pulley (N), Belt Tensioner (C) and Drive Pulley. Be sure that the upper portion of the Drive Belt (B) is under the A bearings on the Belt Tensioner (C). 14. Using the needlenose pliers, reattach the Belt Tensioner spring (C1). Make sure that the belt tension is correct. Refer to the "Belt Tension Adjustment" section in this manual. Note: This step may require two people. 15. Installation is the reverse procedure. Put the Left Shroud in position first to align the screws for the Right Shroud. Install the top screws first. Note: Self-tapping screws attach the Shrouds to the Frame. B C NOTICE: B e sure not to pinch or cut any cables. Be sure the tabs in the Top Shroud snap into the Main Assembly. D C1 N 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
58
11.
Carefully pull the Pulley Shaft Assembly (H) until it works out of
the Frame and releases the Washer (J), Bumper (K), Bearings (L) and
Bearing Brackets (M).
12.
Installation is the reverse procedure.
NOTICE:
Do not overtighten the crank hardware as this can
damage the bearings. Use these torque specs:
Bracket (G)—approx. 8Nm (6lb-ft)
Locknut (E)—approx. 25Nm (18.5 lb-ft)
13.
Put the Drive Belt (B) onto the Drive Pulley (A). Make sure the Drive
Belt is aligned on the Flywheel pulley (N), Belt Tensioner (C) and Drive
Pulley. Be sure that the upper portion of the Drive Belt (B) is under the
bearings on the Belt Tensioner (C).
14.
Using the needlenose pliers, reattach the Belt Tensioner spring (C1).
Make sure that the belt tension is correct. Refer to the “Belt Tension
Adjustment” section in this manual.
Note:
This step may require two people.
15.
Installation is the reverse procedure. Put the Left Shroud in position
first to align the screws for the Right Shroud. Install the top screws first.
Note:
Self-tapping screws attach the Shrouds to the Frame.
NOTICE:
Be sure not to pinch or cut any cables. Be sure the tabs in
the Top Shroud snap into the Main Assembly.
M
M
L
L
K
J
H
A
B
C1
D
N
C