Schwinn 230 Recumbent Bike 2020 model Service Manual - Page 85

Main Shroud. Be sure not to pinch or cut the cable by placing

Get Schwinn 230 Recumbent Bike 2020 model PDF manuals and user guides View all Schwinn 230 Recumbent Bike 2020 model manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

3. Flex the edges of the Upper Shroud to disengage the inside tabs from the Main Assembly, and slide it up the Console Mast. 4. Using a 6mm hex wrench, remove the indicated hardware from the Console Mast. Slightly pull the Console Mast upward, and disconnect the cables. Set the hardware and Upper Shroud safely aside for reassembly. Discard the old Console Mast. NOTICE: Do not pinch or cut the cables. This step may require two people. X4 6mm 5. Using a #2 Phillips Screwdriver, remove the 6 screws (indicated) that secure the Left Main Shroud. Remove the bottom screws first, and then the top screws. Set the hardware safely aside for reassembly. Slowly remove the Left Main Shroud. Note: The Power Inlet Cable (A1) is attached to the inside of the Left Main Shroud. Be sure not to pinch or cut the cable by placing the Left Main Shroud close to the side of the machine. NOTICE: Do not pinch or cut the cables. A A A1 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
85
6mm
X4
3.
Flex the edges of the Upper Shroud to disengage the inside tabs from
the Main Assembly, and slide it up the Console Mast.
4.
Using a 6mm hex wrench, remove the indicated hardware from the
Console Mast. Slightly pull the Console Mast upward, and disconnect the
cables. Set the hardware and Upper Shroud safely aside for reassembly.
Discard the old Console Mast.
NOTICE:
Do not pinch or cut the cables.
This step may require two people.
5.
Using a #2 Phillips Screwdriver, remove the 6 screws (indicated) that
secure the Left Main Shroud. Remove the bottom screws first, and then
the top screws. Set the hardware safely aside for reassembly. Slowly
remove the Left Main Shroud.
Note:
The Power Inlet Cable (A1) is attached to the inside of the Left
Main Shroud. Be sure not to pinch or cut the cable by placing
the Left Main Shroud close to the side of the machine.
NOTICE:
Do not pinch or cut the cables.
A1
A
A