Schwinn 230 Recumbent Bike 2020 model Service Manual - Page 87

Reinstall the Console Mast and Top Shroud. Installation is

Get Schwinn 230 Recumbent Bike 2020 model PDF manuals and user guides View all Schwinn 230 Recumbent Bike 2020 model manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

10. Use the pliers to unhook the Tension Spring (J) from the Main Frame. Pull back and release the Magnet Arm (K) enough to disengage it from the Motor Pulley Shaft (L). 11. Loosen and remove the two hex head bolts (M) from the Servo Motor (N). 12. Remove the Servo Motor (N). Discard the old Servo Motor. N M K L M J 13. Install the new Servo Motor. Installation is the reverse procedure. NOTICE: Do not touch the Potentiometer (P). Do not pinch or cut the cables. 14. Tie the end of the string at the hole (H) in the Mast to the end of the Console Cable (G) on the new Servo Motor. Carefully pull the cable through the hole to the top of the Mast mount. Untie the string and discard it. G 15. Reinstall the Console Mast and Top Shroud. Installation is the reverse procedure. 16. Turn the power on. by plugging in the machine. Machine is on. Current is active. There is risk of electrical shock. 17. Use the console to set the resistance to the highest level. Unplug the machine. Disconnect all power and allow to sit for 5 minutes. 87 P H

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
87
10.
Use the pliers to unhook the Tension Spring (J) from the Main
Frame. Pull back and release the Magnet Arm (K) enough to disengage it
from the Motor Pulley Shaft (L).
11.
Loosen and remove the two hex head bolts (M) from the Servo Motor
(N).
12.
Remove the Servo Motor (N). Discard the old Servo Motor.
13.
Install the new Servo Motor. Installation is the reverse procedure.
NOTICE:
Do not touch the Potentiometer (P). Do not pinch or cut
the cables.
14.
Tie the end of the string at the hole (H) in the Mast to the end of
the Console Cable (G) on the new Servo Motor. Carefully pull the cable
through the hole to the top of the Mast mount. Untie the string and
discard it.
15.
Reinstall the Console Mast and Top Shroud. Installation is the
reverse procedure.
16.
Turn the power on. by plugging in the machine.
Machine is on. Current is active. There is risk of electrical
shock.
17.
Use the console to set the resistance to the highest level. Unplug the
machine.
Disconnect all power and allow to sit for 5 minutes.
M
J
K
N
L
G
P
H
M