Sony RM-VL900 Operating Instructions (primary manual) - Page 28

Follow Steps 3 to 6 on, s 24 and 25, While holding S set, pressed, press VCR.

Get Sony RM-VL900 - Integrated Remote Commander PDF manuals and user guides View all Sony RM-VL900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

Executing a Series of Commands - System Control Function (continued) If a series of commands is already programmed on that button To program a new series of operations, clear the program first (page 28). 3 Follow Steps 3 to 6 on pages 24 and 25 To execute the series of commands Press and hold the programmed Component button for more than 2 seconds. Notes • You can program the System Control function on a Component Select button on which the Power-On function (page 30) has been programmed. In this case, the PowerOn function is overwritten and cannot be used. If you clear the System Control function on the button, the Power-On function is resumed and you can use it again. • You cannot program the System Control function on a Component Select button on which a signal has been programmed by the Learning function (page 15). • You can program a signal on a Component Select button by Learning (page 15) on which the System Control function has been programmed. In this case, the System Control function is overwritten and cannot be used. If you clear the "learned" signal on the button, the System Control function is resumed and you can use it again. • You can program the Power-On function (page 30) on a Component Select button on which the System Control function has been programmed, but the Power-On function cannot be used. If you clear the System Control function on the button, you can use the Power-On function. • If you interrupt the procedure at any point for over 10 seconds, the setting mode ends and the series of commands will be programmed to that point. In this case, clear the program and start again from Step 1 to set the entire program from the beginning. You can not continue from where you let off. • If you change the component code number (page 8) or program a new signal by Learning (page 15) on a button that has been programmed in the series of commands of the System Control function, the new signal will be transmitted when you press the corresponding Component Select button. To clear the System Control function programmed on the Components Select buttons Example: To clear the programmed commands on the VCR button While holding S (set) pressed, press VCR. The Component button lights up when you press them, and turns off when you release them. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
28
Executing a Series of Commands
— System Control Function
(continued)
If a series of commands is
already programmed on
that button
To program a new series of
operations, clear the program first
(page 28).
3
Follow Steps 3 to 6 on
pages 24 and 25
To execute the series of
commands
Press and hold the programmed
Component button for more than
2 seconds.
Notes
• You can program the System Control
function on a Component Select
button on which the Power-On
function (page 30) has been
programmed. In this case, the Power-
On function is overwritten and
cannot be used. If you clear the
System Control function on the
button, the Power-On function is
resumed and you can use it again.
• You cannot program the System
Control function on a Component
Select button on which a signal has
been programmed by the Learning
function (page 15).
• You can program a signal on a
Component Select button by
Learning (page 15) on which the
System Control function has been
programmed. In this case, the System
Control function is overwritten and
cannot be used. If you clear the
“learned” signal on the button, the
System Control function is resumed
and you can use it again.
• You can program the Power-On
function (page 30) on a Component
Select button on which the System
Control function has been
programmed, but the Power-On
function cannot be used. If you clear
the System Control function on the
button, you can use the Power-On
function.
• If you interrupt the procedure at any
point for over 10 seconds, the setting
mode ends and the series of
commands will be programmed to
that point.
In this case, clear the
program and start again from Step 1
to set the entire program from the
beginning. You can not continue from
where you let off.
• If you change the component code
number (page 8) or program a new
signal by Learning (page 15) on a
button that has been programmed in
the series of commands of the System
Control function, the new signal will
be transmitted when you press the
corresponding Component Select
button.
To clear the System Control
function programmed on the
Components Select buttons
Example: To clear the
programmed commands on the
VCR button
While holding S (set)
pressed, press VCR.
The Component button lights
up when you press them, and
turns off when you release
them.