Sony STR-DA2100ES Operating Instructions for STRDA2100ES - Page 59

Performing several commands in sequence automatically (Macro Play

Get Sony STR-DA2100ES - Am/fm Es Stereo Receiver PDF manuals and user guides View all Sony STR-DA2100ES manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Operations Using the Remote RM-AAE001 Performing several commands in sequence automatically (Macro Play) The Macro Play function lets you link several IR codes in a sequential order as a single command. The remote provides 2 macro lists (M1 and M2). You can specify up to 10 IR codes for each macro list. Setting the sequence of IR codes 1 Hold down RM SET UP and press TV ?/1. The indicator lights up and "LEARN" appears in the display. 2 Move the Easy scroll key (PUSH) to select "M1" or "M2". 3 Press the numeric buttons to select the macro step number. For example, to program step 1, press 1. The indicator flashes slowly. 4 Point the remote control code receiver section of the remote towards the receiver/transmitter on the remote control to be learned. 5 Press the appropriate button on the remote control to be learned to send the remote button code. Lightly pressing the button once should be sufficient. If learning is completed successfully, the indicator slowly flashes twice and the remote automatically exits the learning mode. When learning is not completed successfully, the indicator flashes 4 times in quick succession and the procedure returns to step 5. 6 Repeat steps 1 through 5 to program up to 10 IR codes. Tip If programming is unsuccessful, check the following: - If the indicator does not light up in step 1, the batteries are weak. Replace both batteries. - If the indicator lights 4 times in quick succession in step 4, an error has occurred. Start again from step 1. To cancel programming Press RM SET UP during any step. The remote automatically exits the macro setting mode. To delay the output of an IR code Delay each macro step individually. In step 3, press PUSH within 2 seconds. 1 second delay is programmed at this program step. The indicator lights up twice slowly, then the remote automatically exits the macro setting mode. To clear the programmed IR codes Clear each macro step individually. In step 3, press PUSH for more than 2 seconds. The IR code is cleared. The indicator lights up twice slowly, then the remote automatically exits the macro setting mode. To start macro play Move the Easy scroll key (PUSH) to select "M1" or "M2". Note If the Macro Play function does not work properly, program a delay between each operation. See "To delay the output of an IR code". 59US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Operations Using the Remote RM-AAE001
59
US
The Macro Play function lets you link several IR
codes in a sequential order as a single command.
The remote provides 2 macro lists (M1 and M2).
You can specify up to 10 IR codes for each
macro list.
Setting the sequence of IR codes
1
Hold down RM SET UP and press
TV
?/1
.
The indicator lights up and “LEARN”
appears in the display.
2
Move the Easy scroll key (PUSH) to
select “M1” or “M2”.
3
Press the numeric buttons to select the
macro step number.
For example, to program step 1, press 1.
The indicator flashes slowly.
4
Point the remote control code receiver
section of the remote towards the
receiver/transmitter on the remote
control to be learned.
5
Press the appropriate button on the
remote control to be learned to send
the remote button code.
Lightly pressing the button once should be
sufficient.
If learning is completed successfully, the
indicator slowly flashes twice and the
remote automatically exits the learning
mode.
When learning is not completed
successfully, the indicator flashes 4 times in
quick succession and the procedure returns
to step 5.
6
Repeat steps 1 through 5 to program
up to 10 IR codes.
Tip
If programming is unsuccessful, check the following:
–
If the indicator does not light up in step 1, the
batteries are weak. Replace both batteries.
–
If the indicator lights 4 times in quick succession
in step 4, an error has occurred. Start again from
step 1.
To cancel programming
Press RM SET UP during any step. The remote
automatically exits the macro setting mode.
To delay the output of an IR code
Delay each macro step individually. In step
3
,
press PUSH within 2 seconds.
1 second delay is programmed at this program
step. The indicator lights up twice slowly, then
the remote automatically exits the macro setting
mode.
To clear the programmed IR
codes
Clear each macro step individually. In step
3,
press
PUSH
for more than 2 seconds.
The IR code is cleared. The indicator lights up
twice slowly, then the remote automatically
exits the macro setting mode.
To start macro play
Move the Easy scroll key (PUSH) to select
“M1” or “M2”.
Note
If the Macro Play function does not work properly,
program a delay between each operation. See “To
delay the output of an IR code”.
Performing several
commands in sequence
automatically
(Macro Play)