Whirlpool WFC8090GX Installation Instructions - Page 25

Electrical Requirements, Canada Only, Electrical Installation - U.S.A. Only

Get Whirlpool WFC8090GX PDF manuals and user guides View all Whirlpool WFC8090GX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Electrical Requirements - Canada Only Electrical Installation - U.S.A. Only Before you start: disconnect power. 1. Choose electrical connection type Power supply cord 4-wire receptacle (NEMA-Type 14-30R): Go to "Power Supply Cord Connection." It is your responsibility: ■■ To contact a qualified electrical installer. ■■ To be sure that the electrical connection is adequate and in conformance with the Canadian Electrical Code, C22.1 - latest edition and all local codes. A copy of the above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA. ■■ To supply the required 4-wire, single-phase, 120/240 volt, 60 Hz., AC only electrical supply on a separate 30 amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. ■■ This washer/dryer is equipped with a CSA International Certified Power Cord intended to be plugged into a standard 14-30R wall receptacle. The cord is 5 ft. (1.5 m) in length. Be sure wall receptacle is within reach of washer/dryer's final location. ■■ Do not use an extension cord. 4-wire receptacle (14-30R) If using a replacement power supply cord, it is recommended that you use Power Supply Cord Replacement Part Number 8579325. For further information, please reference the "Assistance or Service" section. Power supply cord 3-wire receptacle (NEMA Type 10-30R): Go to "Power Supply Cord Connection." NOTE: If local codes do not permit connection of a cabinet-ground conductor to neutral wire, go to "Optional External Ground for 3-Wire Connection." 2. Remove terminal block cover Remove hold-down screws and terminal block cover. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
25
Electrical Requirements –
Canada Only
It is your responsibility:
■
To contact a qualified electrical installer.
■
To be sure that the electrical connection is adequate
and in conformance with the Canadian Electrical Code,
C22.1 – latest edition and all local codes. A copy of the
above codes standard may be obtained from: Canadian
Standards Association, 178 Rexdale Blvd., Toronto, ON
M9W 1R3 CANADA.
■
To supply the required 4-wire, single-phase, 120/240 volt,
60 Hz., AC only electrical supply on a separate 30 amp
circuit, fused on both sides of the line. A time-delay fuse
or circuit breaker is recommended. Connect to an individual
branch circuit.
■
This washer/dryer is equipped with a CSA
International Certified Power Cord intended
to be plugged into a standard 14-30R wall
receptacle. The cord is 5 ft. (1.5 m) in
length. Be sure wall receptacle is within
reach of washer/dryer’s final location.
■
Do not use an extension cord.
If using a replacement power supply cord, it is recommended
that you use Power Supply Cord Replacement Part Number
8579325. For further information, please reference the
“Assistance or Service” section.
Electrical Installation – U.S.A. Only
Remove hold-down screws and terminal block cover.
1.
Choose electrical connection type
Power supply cord 4-wire receptacle
(NEMA-Type 14-30R):
Go to “Power Supply Cord Connection.”
Power supply cord 3-wire receptacle
(NEMA Type 10-30R):
Go to “Power Supply Cord Connection.”
NOTE:
If local codes do not permit connection of a
cabinet-ground conductor to neutral wire, go to “Optional
External Ground for 3-Wire Connection.”
2.
Remove terminal block cover
Before you start: disconnect power.
4-wire receptacle
(14-30R)