Whirlpool WFC8090GX Installation Instructions - Page 41

Drying Results cont.

Get Whirlpool WFC8090GX PDF manuals and user guides View all Whirlpool WFC8090GX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

TROUBLESHOOTING First try the solutions suggested here or visit our website at www.whirlpool.com/owners (in Canada www.whirlpool.ca/owners) for assistance and to possibly avoid a service call. If you experience Possible Causes Solution Drying Results (cont.) Lint on load Drain pump filter is clogged with lint. Clean the drain pump filter. See "Cleaning the Drain Pump Filter/ Draining Residual Water." This procedure should be performed every 6 months. Dried loads are wrinkled The load was not removed from Remove garments promptly at the end of the drying cycle, washer/dryer at the end of the drying or use the Wrinkle Shield™ option (see "Using the All-In-One cycle. Washer/Dryer"). The washer/dryer was tightly packed. Dry smaller loads that can tumble freely. Loading drum half full or less will improve drying performance and cycle time. Results may also vary depending on fabric type. Load too hot Load removed before cool-down portion of cycle complete. Allow the drying cycle to complete the cool-down portion of the cycle before removing the load. If you cancel the cycle before the cool-down portion of the cycle and immediately remove the load, it will be very hot. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
41
TROUBLESHOOTING
If you experience
Possible Causes
Solution
Drying Results (cont.)
Lint on load
Drain pump filter is clogged with lint.
Clean the drain pump filter. See “Cleaning the Drain Pump Filter/
Draining Residual Water.” This procedure should be performed
every 6 months.
Dried loads are wrinkled
The load was not removed from
washer/dryer at the end of the drying
cycle.
Remove garments promptly at the end of the drying cycle,
or use the Wrinkle Shield
™
option (see “Using the All-In-One
Washer/Dryer”).
The washer/dryer was tightly packed.
Dry smaller loads that can tumble freely. Loading drum half full
or less will improve drying performance and cycle time. Results
may also vary depending on fabric type.
Load too hot
Load removed before cool-down
portion of cycle complete.
Allow the drying cycle to complete the cool-down portion of the
cycle before removing the load. If you cancel the cycle before
the cool-down portion of the cycle and immediately remove the
load, it will be very hot.
First try the solutions suggested here or visit our website at
www.whirlpool.com/owners
(in Canada
www.whirlpool.ca/owners
) for assistance and to possibly avoid a service call.