Whirlpool WFC8090GX Installation Instructions - Page 27

Wire Power Supply Cord Strain Relief

Get Whirlpool WFC8090GX PDF manuals and user guides View all Whirlpool WFC8090GX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

3. Connect ground wire D 3-Wire Power Supply Cord Connection Use where local codes permit connecting cabinet-ground B conductor to neutral wire. 3-wire receptacle (NEMA-type 10-30R) 3 prong plug Connect ground wire (D) (green or bare) of power supply cord under green external ground conductor screw (B). Tighten screw. 4. Connect remaining wires Spade terminals with upturned ends Ring terminals 1. Connect neutral (center) wire A C Connect remaining wires under outer terminal block screws. Tighten screws and also tighten strain relief screws. Finally, install terminal box cover and secure with the three screws. Now, go to "Route Drain Hose." 3-Wire Power Supply Cord Strain Relief: IMPORTANT: Use the strain relief supplied with the washer/dryer. Connect neutral (center) wire (C) of power supply cord under center terminal block screw (A). Tighten screw. 2. Connect remaining wires Attach power supply cord to strain relief Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. Do not further tighten strain relief screws at this point. Connect remaining wires under outer terminal block screws. Tighten screws and also tighten strain relief screws. Finally, install terminal block cover and secure with the three screws. Now, go to "Route Drain Hose." 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
27
3-wire receptacle
(NEMA-type 10-30R)
3 prong plug
Spade terminals
with upturned ends
Ring terminals
4.
Connect remaining wires
Connect remaining wires under outer terminal block screws.
Tighten screws and also tighten strain relief screws. Finally,
install terminal box cover and secure with the three screws.
Now, go to “Route Drain Hose.”
3-Wire Power Supply Cord Connection
Use where local codes permit connecting cabinet-ground
conductor to neutral wire.
2.
Connect remaining wires
Connect remaining wires under outer terminal block screws.
Tighten screws and also tighten strain relief screws. Finally,
install terminal block cover and secure with the three screws.
Now, go to “Route Drain Hose.”
Connect neutral (center) wire (C) of power supply cord
under center terminal block screw (A)
. Tighten screw.
3-Wire Power Supply Cord Strain Relief:
IMPORTANT:
Use the strain relief supplied with the washer/dryer.
Attach power supply cord to strain relief
Put power supply cord through the strain relief. Be sure
that the wire insulation on the power supply cord is inside
the strain relief. Do not further tighten strain relief screws
at this point.
Connect ground wire (D) (green or bare) of power supply
cord under green external ground conductor screw (B).
Tighten screw.
3.
Connect ground wire
1.
Connect neutral (center) wire
D
B
C
A