Home » Yamaha Manuals » Musical Instruments » Yamaha CVP-203 » Manual Viewer

Yamaha CVP-203 Owner's Manual - Page 153

CVP-205/205M: Keyboard Stand Assembly

Add to My Manuals
Save this manual to your list of manuals

Page 153 highlights

CVP-205/205M: Keyboard Stand Assembly CAUTION I Be careful not to confuse parts, and be sure to install all parts in the correct direction. Please assemble in accordance with the sequence given below. I Assembly should be carried out by at least two persons. I Be sure to use the correct screw size, as indicated below. Use of incorrect screws can cause damage. I Be sure to tighten up all screws upon completing assembly of each unit. Have a Phillips-head (+) I To disassemble, reverse screwdriver ready. the assembly sequence given below. 1 Open the package, take out the pedal box, take out the styrofoam pads, and place the main unit on top of the pads. Position the pads so that they will protect the headphone jack and the connector panel located underneath the front left corner, and the ﬂoppy disk drive located underneath the front right corner. Main unit Floppy disk drive Phones jacks Connector panel Styrofoam pads Remove the parts shown below from the box. Front panel Rear panel 3 Attach the front panel. 1 Align and attach the front panel to the front side of the pedal box and both side panels. 2 Secure the panel using the 4x14mm thin screws. * Insert six screws into the smaller holes on the brackets. 4 Mount the main unit. CAUTION • Fingers can become pinched between the main unit and the rear or side panels, be extra careful so as not to drop the main unit. • Do not hold the keyboard in any position other than the position shown in the illustration. Be sure to place your hands at least 10 cm from either end of the main unit when positioning it. Pedal box Pedal cord Side panel (left) Assembly Parts Side panel (right) AC power cord 6 x 25 mm long screws x4 6 x 16 mm short screws x4 4 x 20 mm tapping screws x5 4 x 14 mm thin screws x8 Cord holders x2 2 Attach the side panels to the pedal box. Side panel (left) 2 Remove the vinyl tie from the folded pedal cord. Do not remove the vinyl tie located next to the hole. Side panel (right) 1 Use the four 6x25 mm long screws to attach the pedal box. First attach one side panel, then attach the other side panel. At least 10 cm 5 Fix the main unit. 1 Center the main unit to produce equal clearance on the left and right sides. 2 Use 6x16 mm short screws to secure the main unit from the rear. * Use the front hole on the front brackets to attach the screws. CVP-205/203 153

Section	Page
CVP205,3_E2.pdf	3
About this Owner’s Manual and Data List	5
Accessories	6
“Music Software Collection” Disk (and Music Book) (CVP-203 only)	6
“50 greats for the Piano” Disk (and Music Book)	6
Recording disk	6
Owner’s Manual	6
Data List	6
Bench	6
Handling the Floppy Disk Drive (FDD) and Floppy Disk	6
Compatible Disk Type	6
Inserting/Ejecting Floppy Disks	6
To insert a floppy disk into the disk drive:	6
To eject a floppy disk:	6
Cleaning the Disk Drive Read/Write Head	7
About the Floppy Disks	7
To handle floppy disks with care:	7
To protect your data (Write-protect Tab):	7
Data backup	7
About the Display Messages	8
Maintenance	8
Tuning	8
Transporting	8
Application Index	12
What can you do with the Clavinova?	14
SONG	14
GUIDE	14
DEMO	14
STYLE	14
DIGITAL RECORDING	14
LCD	15
MUSIC FINDER	15
TO HOST terminal	15
PIANO	15
VOICE	15
Setting Up the Clavinova	16
To open the key cover:	16
To close the key cover:	16
To raise the music stand:	16
To lower the music stand:	16
To open	16
To close	16
Connect the power cord.	17
Adjusting the display contrast	17
Setting the volume	17
Panel Controls and Terminals	18
Quick Guide	20
Playing the Demos	20
Song Playback	21
Playback of Songs	21
Playing Voices	25
Playing a Voice	25
Playing Two Voices Simultaneously	26
Playing Different Voices with the Left and Right Hands	27
Playing Styles	28
Playing a style	28
Style Sections	30
Accompaniment Structure	31
One Touch Setting	32
Music Finder	33
Using the Music Finder	33
Searching the Music Finder Records	34
Saving and Recalling Music Finder Data	35
Playing and Practicing with the Songs	36
Playing Along with the Clavinova	36
Recording	37
Mastering Your Favorite Songs	38
Basic Operations — Organizing Your Data	39
Selecting Files and Folders	41
File/Folder-related Operations	42
Naming Files/Folders	42
Moving Files/Folders	43
Copying Files/Folders	44
Deleting Files/Folders	44
Saving Files	45
Organizing Files by Creating a New Folder	45
Displaying Upper Level pages	45
Entering Characters and Changing Icons	45
Entering Characters	46
Converting into Kanji (Japanese language)	46
Entering special character marks (umlaut, accent, Japanese “” and “”)	46
Entering miscellaneous characters (marks)	46
Entering numbers	46
Changing the Icon	47
Using the [DATA ENTRY] Dial	47
Adjusting values	47
Selecting items	47
Direct Access — Instant Selection of Displays	48
Help Messages	50
Using the Metronome	51
Adjusting the Tempo	51
Tap Tempo	52
Tempo Indications — MAIN Display	52
Reference	53
Playing the Demos	53
Voices	55
Selecting a Voice	55
One-touch Piano Play	56
Layer/Left — Playing Several Sounds Simultaneously	57
Layer — Layering Two Different Voices	57
Left — Setting Separate Voices for the Left and Right Sections of the Keyboard	58
Applying Voice Effects	58
REVERB	58
DSP	58
VARIATION (Regular voice only; page89)	58
HARMONY/ECHO	59
MONO	59
LEFT HOLD	59
Using the Pedals	59
Damper Pedal (Right)	59
Sostenuto Pedal (Center)	59
Left Pedal	59
Foot Controller/Footswitch	59
Styles	60
Playing a style	60
Playing a Style’s Rhythm Channels only	62
Adjusting the Volume Balance/Channel Muting	62
Chord Fingerings	63
Arranging the Style Pattern (SECTIONS: MAIN A/B/C/D, INTRO, ENDING, BREAK)	65
Stopping the Style Playback While Releasing Keys (SYNC. STOP)	66
Selecting Intro and Ending Types (INTRO/ENDING)	67
Playing Fill-in patterns automatically when changing accompaniment sections — Auto Fill In	67
Appropriate Panel Setting for the Selected Style (ONE TOUCH SETTING)	68
Automatically Changing One Touch Settings with the Sections — OTS Link	69
Registering the Panel Controls in One Touch Setting (ONE TOUCH SETTING)	69
Calling Up Ideal Setups for Your Music — Music Finder	70
Searching the Ideal Setups — Music Finder Search	71
[A] MUSIC	71
[B] KEYWORD	71
[C] STYLE	71
[D] BEAT	71
[E] SEARCH AREA	71
[F]~[H] CLEAR	71
[1st] TEMPO FROM	71
[2st]TEMPO TO	71
[3st]~[5st] GENRE	71
[8t] CANCEL	71
Editing Records — Music Finder Record Edit	72
[A] MUSIC	72
[B] KEYWORD	72
[C] STYLE	72
[D] BEAT	72
[E] FAVORITE	72
[F]~[H] CLEAR	72
[I] DELETE RECORD	72
[J] NEW RECORD	73
[1ts] TEMPO	73
[3ts]~[5ts] GENRE	73
[6ts] GENRE NAME	73
[8s] OK	73
[8t] CANCEL	73
Song Playback	74
Compatible Song Types	74
Song Playback	75
Playing the Internal Songs	75
Playing Back Songs on Disk	77
Other Playback-related Operations	77
Repeat / Rewind / Fast forward	77
Adjusting the Volume Balance / Muting Specific Channels	77
Muting Specific Parts — Track1/Track2/Extra Tracks	78
Repeat Playback of a Specific Range	78
Using the Practice Functions —Guide	79
Practice Functions	79
For keyboard performance	79
Follow Lights	79
Any Key	79
For sing-along performance	79
Karao-Key	79
Practicing Music with the Guide Functions	80
Displaying Music Notation — Score (CVP-205 only)	81
[1st] LEFT CH/[2st] RIGHT CH	82
[3st], [4st] KEY SIGNATURE	82
[5st] QUANTIZE	82
Note resolution:	82
[6st] NOTE NAME	83
[8s] OK	83
[8t] CANCEL	83
Displaying the Lyrics	84
Saving and Recalling Custom Panel Setups — Registration Memory	85
Registering Panel Setups — Registration Memory	85
Saving Your Registration Memory Setups	86
Recalling a Registration Memory Setup	87
Recalling the Registered Settings	87
Selecting the Freeze Settings	87
Editing Voices — Sound Creator	88
Operation	88
SOUND CREATOR Parameters	89
PIANO (Piano Voice has been selected)	90
COMMON	90
SOUND (Regular Voice only)	90
FILTER	91
EG	91
VIBRATO	91
EFFECT	92
HARMONY	92
Recording Your Performances and Creating Songs — Song Creator	93
About Song Recording	93
Quick Recording (page94)	93
Multi Recording (page95)	93
Step Recording (page97)	93
Song Editing (page103)	93
Quick Recording	94
When creating a new song:	94
Play back your new song	94
Multi Recording	95
When creating a new song:	95
Recording Individual Notes — Step Record	97
Operation	97
Measure/Beat/Clock	98
Velocity	98
Gate Time	98
Recording Melodies — Step Record (Note)	99
Play back the newly created melody	99
Recording Chord Changes for the Auto Accompaniment — Step Record (Chord)	100
Entering Chords and Sections (Chord Step)	100
Play back the newly created chord progression	101
Select the Recording Options: Starting, Stopping, Punching In/Out — Rec Mode	102
Editing a Recorded Song	103
Editing Channel-related Parameters — Channel	103
Quantize	103
About Quantize Size	103
Delete	104
Mix	104
Channel Transpose	105
Set Up	105
Editing Note Events — 1 - 16	106
Editing Chord Events — CHD	107
Editing System Events — SYS/EX. (System Exclusive)	107
Inputting and Editing Lyrics	108
Customizing the Event List — Filter	108
Creating Accompaniment Styles — Style Creator	109
About Creating Accompaniment Styles	109
Realtime Recording (page111)	109
Step Recording (page112)	109
Assembling an Accompaniment Style (page113)	109
Editing the created Accompaniment Style (page114)	109
Style File Format	110
Operation	110
Realtime Recording — Basic	111
Step Recording	112
Assembling an Accompaniment Style —Assembly	113
Edit the Created Accompaniment Style	114
Change the Rhythmic Feel — Groove and Dynamics	114
Groove	114
Dynamics	115
Editing the Channel Data	116
Quantize	116
Velocity Change	116
Bar Copy	116
Bar Clear	116
Remove Event	116
Making Style File Format Settings —Parameter	117
Source Root/Chord	117
NTR (Note Transposition Rule) and NTT (Note Transposition Table)	117
High Key/Note Limit	118
RTR (Retrigger Rule)	118
Adjust the Volume Balance and Changing Voices — Mixing Console	119
Operation	119
About the parameters	119
Setting the Level Balance and Voice — Volume/Voice	120
Changing the Tone of the Voice — Filter	121
Changing Pitch-related Settings — Tune	121
Adjusting the Effects	122
Effect Structure	124
Making Global and Other Important Settings — Function	125
Operation	125
Adjusting the Pitch and Tuning — Master Tune and Scale Tune	125
Master Tune (page127)	125
Scale Tune (page127)	125
Setting Song-related Parameters — Song Settings (page129)	125
Setting Auto Accompaniment-related Parameters — Style Setting, Split Point, and Chord Fingering	125
Style Setting / Split Point (page130)	125
Chord Fingering (page131)	125
Making Settings for the Pedals and Keyboard — Controller	126
Pedal (page131)	126
Keyboard / Panel (page133)	126
Setting the Registration Sequence, Freeze, and Voice Set	126
Registration Sequence (page134)	126
Freeze (page134)	126
Voice Set (page135)	126
Setting Harmony and Echo (page135)	126
Showing the Clavinova Display on a TV — Video Out (CVP-205 only) (page136)	126
Making MIDI Settings	126
System (page137)	126
Transmit (page138)	126
Receive (page139)	126
Root (page139)	126
Chord Detect (page139)	126
Other Settings — Utility	126
Config 1 (page140)	126
Config 2 (page141)	126
Disk (page142)	126
Owner (page143)	126
System Reset (page143)	126
Fine Tuning the Pitch/Selecting a Scale — Master Tune/Scale Tune	127
Tuning the Overall Pitch — Master Tune	127
Selecting a Scale — Scale Tune	127
Scale	128
Equal Temperament	128
Pure Major/Pure Minor	128
Pythagorean	128
Mean-Tone	128
Werckmeister/Kirnberger	128
Arabic	128
Setting Song-related Parameters — Song Settings	129
Setting Auto Accompaniment-related Parameters — Style Setting, Split Point, and Chord Fingering	130
Setting Auto Accompaniment-related Parameters — Style Setting and Split Point	130
Setting the Fingering Method — Chord Fingering	131
Making Settings for the Pedals and Keyboard — Controller	131
Making Settings for the Pedals	131
Pedal-controllable Functions	132
Changing the Touch Sensitivity and Transpose — Keyboard/Panel	133
Keyboard Touch	133
Transpose Assign	133
Setting the Registration Sequence, Freeze, and Voice Set	134
Specifying the Order for Calling Up Registration Memory Presets — Registration Sequence	134
Maintaining Panel Settings — Freeze	134
Changing the Automatically Selected Voice Settings — Voice Set	135
Setting Harmony and Echo	135
About the Harmony Types	136
When a normal Harmony type (“Standard Duet” through “Strum”) is selected	136
When “Multi Assign” is selected	136
When “Echo” is selected	136
When “Tremolo” is selected	136
When “Trill” is selected	136
About the Harmony Assignments	136
Showing the Clavinova Display on a TV — Video Out (CVP-205 only)	136
Setting the MIDI Parameters	137
Making Overall System Settings (Local Control, Clock, etc.) — System	137
Local Control	137
Clock, Transmit Clock, Receive Transpose, Start/Stop	138
Clock	138
Transmit Clock	138
Receive Transpose	138
Start/Stop	138
Message Switch	138
Transmitting MIDI Data — Transmit	138
Receiving MIDI Data — Receive	139
Setting Root Note Channels — Root	139
Setting Chord Channels — Chord Detect	139
Other Settings — Utility	140
Making Settings for Fade In/Out, Metronome, Parameter Lock, and Tap — CONFIG 1	140
Fade In Time, Fade Out Time, Fade Out Hold Time	140
Metronome	140
Parameter Lock	141
Tap Count	141
Making Settings for the Display, Speaker System, and Voice Number Indication — CONFIG 2	141
Copying and Formatting Disks — Disk	142
Entering Your Name and Language Preference — Owner	143
Restoring the Factory-programmed Settings of the CVP-205/203 — System Reset	143
Using Your Clavinova with Other Devices	144
1 Using the Headphones (PHONES jacks).	144
2 Connecting the Microphone or Guitar (MIC./LINE IN jack) (CVP-205 only).	144
345 Connecting Audio & Video Devices	145
3 Playing the sounds of the Clavinova through an external audio system, and recording the sounds ...	145
4 Outputting the sound of an external device through the built-in speakers of the Clavinova (AUX ...	145
5 Showing the display of the Clavinova on a connected TV monitor (VIDEO OUT) (CVP-205 only)	145
6 Using the Pedal (footswitch) or Foot Controller (AUX PEDAL jack)	146
7 Connecting external MIDI devices (MIDI terminals)	146
8 Connecting to a Computer (MIDI terminals/TO HOST terminal)	146
Using the TO HOST terminal	147
IBM-PC/AT (Windows)	147
Macintosh	147
Using the MIDI terminals	147
Using the USB terminal on your computer with a USB/MIDI interface (UX256/UX96, etc.)	148
What’s MIDI?	148
Example Keyboard Data	149
Channel Messages	149
MIDI channels	150
System Messages	150
What You Can Do With MIDI	150
Data Compatibility	151
Disk format	151
Sequence Format	151
SMF (Standard MIDI File)	151
ESEQ	151
XF	151
Style File	151
Voice Allocation Format	152
GM System Level 1	152
XG	152
DOC	152
CVP-205/205M: Keyboard Stand Assembly	153
After completing the assembly, please check the following.	154
CVP-203: Keyboard Stand Assembly	155
After completing the assembly, please check the following.	156
Troubleshooting	157
Specifications	159

Match case Limit results 1 per page

153

CVP-205/203

CVP-205/205M: Keyboard Stand Assembly

CAUTION

■

Be careful not to confuse parts, and be sure to install

all parts in the correct direction. Please assemble in

accordance with the sequence given below.

■

Assembly should be carried out by at least two persons.

■

Be sure to use the correct screw size, as indicated

below. Use of incorrect screws can cause damage.

■

Be sure to tighten up all screws upon completing

assembly of each unit.

■

To disassemble, reverse

the assembly sequence

given below.

Open the package, take out the pedal box, take out

the styrofoam pads, and place the main unit on top

of the pads.

Position the pads so that they will protect the headphone

jack and the connector panel located underneath the front

left corner, and the

ﬂ

oppy disk drive located underneath

the front right corner.

Remove the parts shown below from the box.

Attach the side panels to the pedal box.

Attach the front panel.

Align and attach the front panel to the front side of the pedal box

and both side panels.

Secure the panel using the 4x14mm thin screws.

* Insert six screws into the

smaller holes

on the brackets.

Mount the main unit.

Be sure to place your hands at least 10 cm from either

end of the main unit when positioning it.

Fix the main unit.

Center the main unit to produce equal clearance on the left and

right sides.

Connector panel

Floppy disk drive

Phones

jacks

Styrofoam pads

Main unit

Front panel

Rear panel

Pedal box

Side panel

(left)

Assembly Parts

AC power cord

Side panel

(right)

Pedal cord

6 x 25 mm long screws x4

4 x 20 mm tapping screws x5

6 x 16 mm short screws x4

Cord holders x2

4 x 14 mm thin screws x8

Side panel

(left)

Side panel

(right)

Side panel

(left)

Side panel

(right)

Remove the vinyl tie from the folded

pedal cord. Do not

remove the vinyl tie

located next to the

hole.

Use the four 6x25 mm

long screws to attach the

pedal box. First attach one

side panel, then attach the

other side panel

CAUTION

•

Fingers can become pinched between the main unit and

the rear or side panels, be extra careful so as not to drop

the main unit.

•

Do not hold the keyboard in any position other than the

position shown in the illustration.

At least

10 cm

At least

10 cm

Use 6x16 mm short

screws to secure the

main unit from the rear.

* Use the front hole on

the front brackets to

attach the screws.

Have a Phillips-head (+)

screwdriver ready.