Yamaha QY300 Owner's Manual - Page 105

Range, ENTER], Phrase, Transpose

Get Yamaha QY300 PDF manuals and user guides View all Yamaha QY300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

The Phrase Jobs The "Range" parameter determines the range of velocity values over which the crescendo will occur. A setting of "+24", for example, will cause the MIDI velocity values to increase by 24 over the specified measure range (The MIDI velocity value range is from 0 to 127). Original velocity Crescendo Specified measure ("M") range. Range +24 Negative values cause a corresponding decrease in velocity, therby producing a decrescendo rather than a crescendo. The range of this parameter is from "- 99" through "0" to "+99". After setting the parameters as required press [ENTER] to execute the Crescendo job. The metronome icon will appear on the display while the data is being processed, then "Completed" will appear briefly when the job is done. Press the [F6] key ("Exit") to return to the job list, or a mode key to go directly to the selected mode. 05: Transpose Transposes all notes in the specified user phrase up or down by the specified number of semitones. The "Phrase" parameter selects the user phrase to be affected by the Transpose job: "001" ... "100". The "Transpose" parameter determines the amount of transposition in semitone increments. Minus (-) values transpose down while plus (+) values transpose up. the range is from "-99" through "0" to "+99". After setting the parameters as required press [ENTER] to execute the Transpose job. The metronome icon will appear on the display while the data is being processed, then "Completed" will appear briefly when the job is done. Press the [F6] key ("Exit") to return to the job list, or a mode key to go directly to the selected mode. 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
97
The Phrase Jobs
The
“Range”
parameter determines the range of velocity values over which
the crescendo will occur. A setting of “+24”, for example, will cause the MIDI
velocity values to increase by 24 over the specified measure range (The MIDI
velocity value range is from 0 to 127).
Negative values cause a corresponding decrease in velocity, therby producing
a decrescendo rather than a crescendo. The range of this parameter is from “–
99” through “0” to “+99”.
After setting the parameters as required press
[ENTER]
to execute the Cre-
scendo job. The metronome icon will appear on the display while the data is
being processed, then “Completed” will appear briefly when the job is done.
Press the
[F6]
key (“Exit”) to return to the job list, or a mode key to go directly
to the selected mode.
05: Transpose
Transposes all notes in the specified user phrase up or down by the specified
number of semitones.
The
“Phrase”
parameter selects the user phrase to be affected by the Trans-
pose job: “001” … “100”.
The
“Transpose”
parameter determines the amount of transposition in
semitone increments. Minus (–) values transpose down while plus (+) values
transpose up. the range is from “–99” through “0” to “+99”.
After setting the parameters as required press
[ENTER]
to execute the Trans-
pose job. The metronome icon will appear on the display while the data is
being processed, then “Completed” will appear briefly when the job is done.
Press the
[F6]
key (“Exit”) to return to the job list, or a mode key to go directly
to the selected mode.
Specified measure (
“
M
”
) range.
Range
+24
Original
velocity
Crescendo