3Com 3C94024 Getting Started Guide - Page 29

System Power Up, Power Up

Get 3Com 3C94024 - CoreBuilder 9400 1000SX Switch PDF manuals and user guides
UPC - 662705154404
View all 3Com 3C94024 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

4 SYSTEM POWER UP This chapter contains: s "Power Up" instructions for the CoreBuilder® 9400 system s A description of "Power-up Diagnostics" s A list of "System Checks" after power up For information on troubleshooting the system during power up, see Chapter 6. Power Up To get your CoreBuilder 9400 powered up and ready to operate, follow the steps in this section. See Chapter 3 and Chapter 5 for information about cabling and configuring the Console port. To view error messages while the system runs power-up diagnostics, connect a terminal, a workstation, or a PC that has terminal emulation to the system's Console port. 1 Verify that the power outlet is near the system and easily accessible. You can turn the system off only by removing the power cord from the power source or from the system itself. 2 On the back panel, slide the power supply latch up and plug the power cord into the power receptacle. See Figure 12 for the location of the power receptacle. Figure 12 CoreBuilder 9400 System Power Receptacle Power supply Power supply latch DC OK ! Power receptacle 3 Plug the other end of the power cable into a power outlet. 4 If you want add an additional power supply, repeat step 2 and step 3 for the second power supply.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
4
S
YSTEM
P
OWER
U
P
This chapter contains:
■
“Power Up” instructions for the
CoreBuilder
®
9400 system
■
A description of “Power-up Diagnostics”
■
A list of “System Checks” after power up
For information on troubleshooting the system during
power up, see Chapter 6.
Power Up
To get your CoreBuilder 9400 powered up and ready
to operate, follow the steps in this section.
See Chapter 3 and Chapter 5 for information about
cabling and configuring the Console port.
To view error messages while the system runs
power-up diagnostics, connect a terminal, a
workstation, or a PC that has terminal emulation to
the system’s Console port.
1
Verify that the power outlet is near the system and
easily accessible. You can turn the system off only by
removing the power cord from the power source or
from the system itself.
2
On the back panel, slide the power supply latch up
and plug the power cord into the power receptacle.
See Figure 12 for the location of the power
receptacle.
Figure 12
CoreBuilder 9400 System Power Receptacle
3
Plug the other end of the power cable into a power
outlet.
4
If you want add an additional power supply, repeat
step 2 and step 3 for the second power supply.
DC
OK
!
Power supply latch
Power supply
Power receptacle