Asus P2-99B P2-99B User Manual - Page 31

Enabled, Power Management Setup

Get Asus P2-99B PDF manuals and user guides View all Asus P2-99B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

GND +12V Rotation III. H/W SETUP Connectors III. HARDWARE SETUP 7. Chassis,CPU,&PowerSupplyFanConnectors(3-pinCHA_,CPU_,PWR_FAN) These connectors support cooling fans of 500mA (6 Watts) or less. Orientate the fans so that the heat sink fins allow airflow to go across the onboard heat sink(s) instead of the expansion slots. Depending on the fan manufacturer, the wiring and plug may be different. The red wire should be positive, while the black should be ground. Connect the fan's plug to the board taking into consideration the polarity of the this connector. NOTE: The "Rotation" signal is to be used only by a specially designed fan with rotation signal. WARNING! These connectors have power. Damage may occur to the motherboard and/or the CPU fan if these connectors are incorrectly used. CPU Fan Power (CPU_FAN) Power Supply Fan (PWR_FAN) GND +12V Rotation P2-99B R P2-99B 12Volt Cooling Fan Power Chassis Fan Power (CHA_FAN) GND +12V Rotation 8. Wake-On-LAN Connector (3-pin WOL_CON) This connector connects to a LAN card with a Wake-On-LAN output, such as the ASUS PCI-L101. The LAN card powers up the system when a wakeup packet or signal is received from the network. IMPORTANT: This feature requires that the WAKE On LAN Power Up Control is set to Enabled (see Power Management Setup under BIOS SETUP) and that your system has an ATX power supply with at least 720mA +5V standby power. P2-99B R Ground +5 VSB PME P2-99B Wake-On-LAN Connector ASUS P2-99B User's Manual 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
ASUS P2-99B User’s Manual
31
III. HARDWARE SETUP
7.
Chassis, CPU , & Power Supply Fan Connectors (3-pin CHA_, CPU_, PWR_FAN)
These connectors support cooling fans of 500mA (6 Watts) or less.
Orientate
the fans so that the heat sink fins allow airflow to go across the onboard heat
sink(s) instead of the expansion slots.
Depending on the fan manufacturer, the
wiring and plug may be different.
The red wire should be positive, while the
black should be ground.
Connect the fan’s plug to the board taking into consid-
eration the polarity of the this connector.
NOTE:
The “Rotation” signal is to
be used only by a specially designed fan with rotation signal.
WARNING!
These connectors have power. Damage may occur to the mother-
board and/or the CPU fan if these connectors are incorrectly used.
P2-99B 12Volt Cooling Fan Power
Chassis Fan Power (CHA_FAN)
Power Supply Fan (PWR_FAN)
CPU Fan Power (CPU_FAN)
GND
Rotation
+12V
P2-99B
GND
Rotation
+12V
GND
Rotation
+12V
8.
Wake-On-LAN Connector (3-pin WOL_CON)
This connector connects to a LAN card with a Wake-On-LAN output, such as
the ASUS PCI-L101. The LAN card powers up the system when a wakeup
packet or signal is received from the network.
IMPORTANT:
This feature requires that the
WAKE On LAN
Power Up Con-
trol
is set to
Enabled
(see
Power Management Setup
under BIOS SETUP
)
and
that your system has an ATX power supply with at least 720mA +5V standby
power.
P2-99B Wake-On-LAN Connector
+5 VSB
PME
Ground
P2-99B
Connectors
III.
H/W SETUP