Asus P2-99B P2-99B User Manual - Page 44

ASUS P2-99B User's Manual, Auto detection of hard disks on bootup, Drive A / Drive B, Floppy 3 Mode

Get Asus P2-99B PDF manuals and user guides View all Asus P2-99B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

IV. BIOS SETUP Auto detection of hard disks on bootup For each field: Primary Master, Primary Slave, Secondary Master, and Secondary Slave, you can select Auto under the TYPE and MODE fields. This will enable auto detection of your IDE hard disk during bootup. This will allow you to change your hard disks (with the power off) and then power on without having to reconfigure your hard disk type. If you use older hard disks that do not support this feature, then you must configure the hard disk in the standard method as described earlier by the "User" option. NOTE: After the IDE hard disk drive information has been entered into BIOS, new IDE hard disk drives must be partitioned (such as with FDISK) and then formatted before data can be read from and write on. Primary IDE hard disk drives must have its partition set to active (also possible with FDISK). NOTE: SETUP Defaults are noted in parenthesis next to each function heading. Drive A / Drive B These fields record the types of floppy disk drives installed in your system. The available options for drives A and B are: 360K, 5.25 in.; 1.2M, 5.25 in.; 720K, 3.5 in.; 1.44M, 3.5 in.; 2.88M, 3.5 in.; None To enter the configuration value for a particular drive, highlight its corresponding field and then select the drive type using the / or / keys. Floppy 3 Mode Support This is the Japanese standard floppy drive. The standard stores 1.2MB in a 3.5inch diskette. This is normally disabled but you may choose from either: Drive A, Drive B, Both, and Disabled Video Set this field to the type of video display card installed in your system. The options are EGA/VGA, CGA 40, CGA 80, and MONO (for Hercules or MDA). If you are using a VGA or any higher resolution card, choose EGA/VGA. Halt On This field determines which types of errors will cause the system to halt. Choose from All Errors; No Errors; All,But Keyboard, All,But Diskette; and All,But Disk/Key. IV. BIOS SETUP Standard CMOS 44 ASUS P2-99B User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
ASUS P2-99B User’s Manual
44
IV.
BIOS SETUP
IV.
BIOS SETUP
Standard CMOS
Auto detection of hard disks on bootup
For each field:
Primary Master, Primary Slave, Secondary Master, and Secondary
Slave, you can select
Auto
under the TYPE and MODE fields.
This will enable auto
detection of your IDE hard disk during bootup.
This will allow you to change your
hard disks (with the power off) and then power on without having to reconfigure
your hard disk type.
If you use older hard disks that do not support this feature, then
you must configure the hard disk in the standard method as described earlier by the
“User” option.
NOTE:
After the IDE hard disk drive information has been entered into BIOS, new
IDE hard disk drives must be partitioned (such as with FDISK) and then formatted
before data can be read from and write on.
Primary IDE hard disk drives must have
its partition set to
active
(also possible with FDISK).
NOTE:
SETUP Defaults are noted in parenthesis next to each function heading.
Drive A / Drive B
These fields record the types of floppy disk drives installed in your system.
The
available options for drives A and B are:
360K, 5.25 in.; 1.2M, 5.25 in.; 720K, 3.5
in.; 1.44M, 3.5 in.; 2.88M, 3.5 in.; None
To enter the configuration value for a particular drive, highlight its corresponding
field and then select the drive type using the <page up>/<page down> or <+>/<->
keys.
Floppy 3 Mode Support
This is the Japanese standard floppy drive.
The standard stores 1.2MB in a 3.5inch
diskette.
This is normally disabled but you may choose from either:
Drive A, Drive
B, Both, and Disabled
Video
Set this field to the type of video display card installed in your system.
The options
are
EGA/VGA
,
CGA 40
,
CGA 80
, and
MONO
(for Hercules or MDA)
.
If you are using a VGA or any higher resolution card, choose
EGA/VGA
.
Halt On
This field determines which types of errors will cause the system to halt.
Choose from
All Errors
;
No Errors
;
All
,
But Keyboard, All
,
But Diskette
; and
All,But Disk/Key.