Asus P2-99B P2-99B User Manual - Page 34

ASUS P2-99B User's Manual, Wake-On-Ring Connector 2-pin WOR, IMPORTANT, PWR UP On Modem Act, Chassis

Get Asus P2-99B PDF manuals and user guides View all Asus P2-99B manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

III. HARDWARE SETUP 18. Wake-On-Ring Connector (2-pin WOR) This connector connects to an internal modem card with a Wake-On-Ring output. The connector powers up the system when a ringup packet or signal is received through the internal modem card. NOTE: For external modems, Wake-On-Ring is detected through the COM port. IMPORTANT: This feature requires that PWR UP On Modem Act Power Up Control is set to Enabled (see Power Management Setup under BIOS SETUP) and that your system has an ATX power supply with at least 720mA +5V standby power. P2-99B R WOR Pin 2 PIXRI# Pin 1 Ground P2-99B Wake-On-Ring Connector 19. Chassis Intrusion Sensor Lead (optional) (4-1 pin CHASIS) This lead is for a chassis intrusion monitor or sensor. The sensor is triggered when a high level signal is sent to the "chassis signal" lead. This occurs when a panel switch or light detector is triggered. This function requires the optional ASUS CIDB Chassis Intrusion Photo Sensor Module (see APPENDIX) to be installed. III. H/W SETUP Connectors +5Volt (Power Supply Stand By) Chassis Signal Ground P2-99B R P2-99B Chassis Open Alarm Lead 34 ASUS P2-99B User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
34
ASUS P2-99B User’s Manual
III. HARDWARE SETUP
Connectors
III.
H/W SETUP
18.
Wake-On-Ring Connector (2-pin WOR)
This connector connects to an internal modem card with a Wake-On-Ring output.
The connector powers up the system when a ringup packet or signal is received
through the internal modem card.
NOTE:
For external modems, Wake-On-Ring
is detected through the COM port.
IMPORTANT:
This feature requires that
PWR UP On Modem Act
Power Up
Control
is set to
Enabled
(see
Power Management Setup
under BIOS SETUP
)
and that your system has an ATX power supply with at least 720mA +5V standby
power.
P2-99B Wake-On-Ring Connector
WOR
P2-99B
Pin 2 PIXRI#
Pin 1 Ground
19. Chassis Intrusion Sensor Lead (optional) (4-1 pin CHASIS)
This lead is for a chassis intrusion monitor or sensor. The sensor is triggered
when a high level signal is sent to the “chassis signal” lead. This occurs when a
panel switch or light detector is triggered. This function requires the optional
ASUS CIDB Chassis Intrusion Photo Sensor Module (see APPENDIX) to be
installed.
P2-99B Chassis Open Alarm Lead
+5Volt (Power Supply Stand By)
Ground
Chassis Signal
P2-99B