Brother International Innov-is NQ550PRW Operation Manual - Page 50

Stitch Setting Chart Stitch Setting Chart Applications, stitch lengths and widths and whether the twin needle can be used are listed for utility stitches in the following table. *1 Patterns printed on the numeric keys on the machine can be selected directly. For details, refer to "Preset utility stitches" on page B-46. *2 For free motion quilting, use free motion open toe quilting foot "O" (sold separately with some models). *3 When automatic reverse/reinforcement stitching has been set, the stitch will begin with reinforcement stitch. If reinforcement priority has been set to " stop. ", the machine will sew reinforcement stitches at the end of stitching and then Note • The walking foot can only be used with straight or zigzag stitch patterns. Do not sew reverse stitches with the walking foot. Stitch Stitch number 01*1 02*1 03*1 04*1 05*1 06*1 07 08*1 09*1 10 11 12*1 13*1 14 Stitch name Straight stitch (Left) Straight stitch (Left) Straight stitch (Middle) Straight stitch (Middle) Triple stretch stitch Stem stitch Basting stitch Zigzag stitch Zigzag stitch Zigzag stitch (Right) 2 steps elastic zigzag stitch 3 steps elastic zigzag stitch Overcasting stitch Overcasting stitch Presser foot Applications General sewing, gather, J*2 pintuck, etc. General sewing, gather, J*2 pintuck, etc. General sewing, gather, J*2 pintuck, etc. General sewing, gather, J*2 pintuck, etc. General sewing for J*2 reinforcement and decorative topstitching Reinforced stitching, sewing J*2 and decorative applications Basting J*2 For overcasting, mending. J*2 For overcasting, mending. J*2 Start from right needle J*2 position, zigzag sews to left. Overcasting (medium weight J*2 and stretch fabrics), tape and elastic Overcasting (medium, J*2 heavyweight and stretch fabrics), tape and elastic Reinforcing of light and G medium weight fabrics Reinforcing of heavyweight G fabric Stitch width [mm (inch)] Auto. Manual Stitch length [mm (inch)] Auto. Manual Twin needle 0.0 (0) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.2 - 5.0 (1/64 - 3/16) OK ( J ) 0.0 (0) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.2 - 5.0 (1/64 - 3/16) OK ( J ) 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.2 - 5.0 (1/64 - 3/16) OK ( J ) 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.2 - 5.0 (1/64 - 3/16) OK ( J ) 0.0 (0) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.4 - 5.0 (1/64 - 3/16) OK ( J ) 1.0 (1/16) 0.0 - 7.0 (0 - 1/4) 2.5 (3/32) 0.4 - 5.0 (1/64 - 3/16) OK ( J ) 0.0 (0) 0.0 - 7.0 - NO (0 - 1/4) 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 1.4 (1/16) 0.0 - 5.0 (0 - 3/16) OK ( J ) 3.5 (1/8) 0.0 - 7.0 (0 - 1/4) 1.4 (1/16) 0.0 - 5.0 (0 - 3/16) OK ( J ) 3.5 (1/8) 2.5 - 5.0 (3/32 - 3/16) 1.4 (1/16) 0.3 - 5.0 (1/64 - 3/16) OK ( J ) 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 1.0 (1/16) 0.2 - 5.0 (1/64 - 3/16) OK ( J ) 5.0 (3/16) 0.0 - 7.0 (0 - 1/4) 1.0 (1/16) 0.2 - 5.0 (1/64 - 3/16) OK ( J ) 3.5 (1/8) 2.0 (1/16) 2.5 - 5.0 0.4 - 5.0 NO (3/32 - 3/16) (1/64 - 3/16) 5.0 (3/16) 2.5 (3/32) 2.5 - 5.0 0.4 - 5.0 NO (3/32 - 3/16) (1/64 - 3/16) Reverse button Reverse Reverse*3 Reverse Reverse*3 Reinforce- ment Reinforce- ment Reinforce- ment Reverse Reverse*3 Reverse*3 Reverse*3 Reverse*3 Reinforce- ment Reinforce- ment B-42