Brother International Innov-is NQ550PRW Operation Manual - Page 97

Deleting a pattern, Sewing attractive finishes

Get Brother International Innov-is NQ550PRW PDF manuals and user guides View all Brother International Innov-is NQ550PRW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

Deleting a pattern To remove a selected pattern, press panel. on the operation  The selected pattern is removed. Sewing the Various Built-in Decorative Patterns Sewing attractive finishes To achieve attractive results when sewing character/decorative stitches, check the table below for the proper fabric/thread/needle combinations. Note • Other factors, such as fabric thickness, stabilizer material, etc., also have an effect on the stitch, so you should always sew a few trial stitches before beginning your project. • It may be necessary to adjust the pattern, depending on the type of fabric being sewn or the sewing speed. Adjust the pattern while sewing trial stitches on a scrap piece of fabric that is the same as what is used in your project. Refer to "Realigning the pattern" on page D-7. • When sewing satin stitch patterns, there may be shrinking or bunching of stitches, so be sure to attach a stabilizer material. • Guide the fabric with your hand to keep the fabric feeding straight and even during sewing. D Fabric When sewing on stretch fabrics, lightweight fabrics, or fabrics with coarse weaves, attach stabilizer on the wrong side of the fabric. An alternative would be to place the fabric on thin paper such as tracing paper. CHARACTER / DECORATIVE STITCHES Memo • If a new pattern is selected without deleting the previously selected one, the first and second patterns are combined. (Refer to "Combining patterns" on page D-5.) • If two patterns or more have been already selected, the pattern that was selected last is removed. • You can delete the entire combined pattern by pressing . Thread Needle Presser foot Twin needle 1 Fabric 2 Stabilizer 3 Thin paper #50 - #60 With lightweight, regular, or stretch fabrics: the Ball point needle (golden colored) 90/14 With heavyweight fabrics: home sewing machine needle 90/14 Monogramming foot "N". Using zigzag foot "J" or other presser feet may give inferior results. You can sew with twin needle (2/11) when you select 7 mm satin stitch pattern. In this case, use zigzag foot "J". Decorative sewing D-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
Sewing the Various Built-in Decorative Patterns
Decorative sewing
D-3
CHARACTER / DECORATIVE STITCHES
D
Deleting a pattern
To remove a selected pattern, press
on the operation
panel.
The selected pattern is removed.
Sewing attractive finishes
To achieve attractive results when sewing
character/decorative stitches, check the table below for the
proper fabric/thread/needle combinations.
Memo
•
If a new pattern is selected without deleting the
previously selected one, the first and second
patterns are combined. (Refer to “Combining
patterns” on page D-5.)
•
If two patterns or more have been already
selected, the pattern that was selected last is
removed.
•
You can delete the entire combined pattern by
pressing
.
Note
•
Other factors, such as fabric thickness, stabilizer
material, etc., also have an effect on the stitch,
so you should always sew a few trial stitches
before beginning your project.
•
It may be necessary to adjust the pattern,
depending on the type of fabric being sewn or
the sewing speed. Adjust the pattern while
sewing trial stitches on a scrap piece of fabric
that is the same as what is used in your project.
Refer to “Realigning the pattern” on page D-7.
•
When sewing satin stitch patterns, there may be
shrinking or bunching of stitches, so be sure to
attach a stabilizer material.
•
Guide the fabric with your hand to keep the
fabric feeding straight and even during sewing.
Fabric
When sewing on stretch fabrics, lightweight
fabrics, or fabrics with coarse weaves, attach
stabilizer on the wrong side of the fabric. An
alternative would be to place the fabric on thin
paper such as tracing paper.
1
Fabric
2
Stabilizer
3
Thin paper
Thread
#50 - #60
Needle
With lightweight, regular, or stretch fabrics: the Ball
point needle (golden colored) 90/14
With heavyweight fabrics: home sewing machine
needle 90/14
Presser foot
Monogramming foot “N”.
Using zigzag foot “J” or other presser feet may
give inferior results.
Twin needle
You can sew with twin needle (2/11) when you
select 7 mm satin stitch pattern. In this case, use
zigzag foot “J”.