Canon FS-4 User Guide - Page 16

Connect the FS-4 to AC Power, Connect the FS-4 to a DV Camcorder - fs 4 0 manual

Get Canon FS-4 - FOCUS FireStore Pro PDF manuals and user guides View all Canon FS-4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

To remove the battery, use the following steps: Step 1: Step 2: Slide the battery latch to the left and slide downward on the battery pack about 1cm or 3/8. Remove the battery pack. Connect the FS-4 to AC Power You can use the FS-4 immediately after you install the battery using AC power. NOTE: You can use the FS-4 without a battery installed. To do this, connect the AC power as follows: Step 1: Step 2: Step 3: Plug the cord from the power supply into the bottom of the FS-4. Connect the line cord to the rectangular power supply (International models only). Plug the line cord or AC adapter into an electric outlet. Connect the FS-4 to a DV Camcorder Before performing this procedure, make sure you have performed "Installing and Removing the Battery Pack" on page 11 and/or "Connect the FS-4 to AC Power" on page 12. Step 1: Connect the supplied Firewire cable to the "DV I/O" connector on the top of the FS-4. (Only one end will match the plug in the FS-4.) Step 2: Step 3: Step 4: Step 5: 12 Locate the FireWire/DV/iLink (or similar) connector on your video camera. It is located in different places depending upon the brand of camera. If you are unclear of its location, consult your video camera manual. Connect the other end of the FireWire cable to your video camera. Turn on the video camera. Turn on the FS-4.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
12
To remove the battery, use the following steps:
Step 1:
Slide the battery latch to the left and slide downward on
the battery pack about 1cm or 3/8.
Step 2:
Remove the battery pack.
Connect the FS-4 to AC Power
You can use the FS-4 immediately after you install the battery using
AC power.
NOTE:
You can use the FS-4 without a battery installed.
To do this, connect the AC power as follows:
Step 1:
Plug the cord from the power supply into the bottom of the
FS-4.
Step 2:
Connect the line cord to the rectangular power supply
(International models only).
Step 3:
Plug the line cord or AC adapter into an electric outlet.
Connect the FS-4 to a DV Camcorder
Before performing this procedure, make sure you have performed
“Installing and Removing the Battery Pack” on page 11 and/or “Con-
nect the FS-4 to AC Power” on page 12.
Step 1:
Connect the supplied Firewire cable to the “DV I/O”
connector on the top of the FS-4. (Only one end will match
the plug in the FS-4.)
Step 2:
Locate the FireWire/DV/iLink (or similar) connector on
your video camera. It is located in different places
depending upon the brand of camera. If you are unclear
of its location, consult your video camera manual.
Step 3:
Connect the other end of the FireWire cable to your video
camera.
Step 4:
Turn on the video camera.
Step 5:
Turn on the FS-4.